The wood on some of the early Crosmans is often amazing when refinished....
https://hosting.photobucket.com/albums/oo221/rsterne/Crosman%20140/.highres/1400RestoredRight.jpg
That was a 1400...
Type: Posts; User: rsterne
Forum: AirGuns
The wood on some of the early Crosmans is often amazing when refinished....
https://hosting.photobucket.com/albums/oo221/rsterne/Crosman%20140/.highres/1400RestoredRight.jpg
That was a 1400...
Forum: AirGuns
That is about their performance.... I visually inspect every pellet or bullet I cast and throw the culls back in the pot, I never size pellets (but I do with bullets, if required).... Sometimes I...
Forum: AirGuns
You need to run the mold very hot to get the skirts to fill out properly.... The best results are using a ladle with a nose on it and pressure pouring....
Bob
Forum: AirGuns
14,000 / 700 = 20 hrs., not 200.... just sayin'....
Bob
Forum: AirGuns
A 2% total ES in pellet weight would cause only a 1% velocity change.... At 50 yards, the trajectory difference will be about a 0.1" difference in the POI.... If you are seeing flyers, I think you...
Forum: AirGuns
I use 40:1, ie 2.5% tin.... Wheel weights are generally too hard for airgun use, you want either pure lead, or a small amount of tin, and keep the BHN under 10....
Bob
Forum: AirGuns
Anyone who can get 1" groups at 100 yards with an airgun deserves your respect, they are few and far between.... Over on the Gateway To Airguns, we have a club called NUAH, which stands for "Nuttin'...
Forum: AirGuns
Huge difference between a .25 cal Condor and a .257 Texan.... just sayin'....
Bob
Forum: AirGuns
I only have experience with one gas-spring airgun, and it broke two supposedly springer rated scopes.... It was harder to cock than the same gun with a coil spring, but did deliver a bit more...
Forum: AirGuns
I know quite a few airgunners use 10 Wt Silicone R/C Shock Oil to sparingly lube their slugs.... I believe a few drops in a baggie, add the slugs and work them around is the technique....
Bob
Forum: AirGuns
Cast the bullets in pure tin, the weight will be 65% of what they would be in lead.... Run that in your calculator and see what you get.... I checked out the Bison Ballistics calculator, and the Sg...
Forum: AirGuns
100 yards in wind is very difficult with pellets, but OK with slugs.... Further than that, you must allow significant drop, but I have seen sub MOA groups achieved with slugs at 200 yards in calm...
Forum: AirGuns
This is a common method for increasing the stiffness of airgun barrels.... Here is a photo of my .257 Condor barrel sleeved with a 26mm OD carbon sleeve over the 16mm barrel, compared to the original...
Forum: AirGuns
If you had a frontal shot on that 'coon and she was looking straight at you, the pellet likely glanced off her skull.... To make that shot work, she would have to have her head down, to make the...
Forum: AirGuns
Target too big?.... move further back....
Bob
Forum: AirGuns
I haven't tried it yet, but the next time I have a 20 lb. Propane tank that is out of date, I am going to cut the round bottom off, level with the bottom of the parallel sides.... I am then going to...
Forum: AirGuns
24X is certainly too much magnification for a 40mm objective, you will notice darkening of the image past about 16X.... I use a 3-12X for hunting gophers out to 100 yd.... The only time I use more...
Forum: AirGuns
Accurate cannot do anything smaller than 0.28"....
Bob
Forum: AirGuns
I've never tried it, but those who have find they lose a lot of velocity, because by the time they size it small enough to not jam in the bore, they get too much blowby.... The jacket material is...
Forum: AirGuns
Interestingly, gas-check style bullets, without the gas check fitted, tend to be very accurate in airguns.... often more so than the same design in a flat base.... It could be the slight difference...
Forum: AirGuns
I do, and I get a LOT of fills, when I am filling to 2000 psi.... Don't discount what you can do with that pressure, my Grouse gun has killed hundreds over the past decade.... Having said that, if...
Forum: AirGuns
I have done only limited testing with the .30 cal "Magnum" pellet from NOE, in a 26" twist TJ's barrel.... It shot well at close range, but was subject to spiralling at longer ranges.... I did not...
Forum: AirGuns
The 68 gr. BBT made by NOE has a calculated minimum twist rate of 27".... I does, in fact, work great from the TJ's 26" twist barrel.... I designed it to work with that.... It is 0.375" long, and the...
Forum: AirGuns
The chamber on the Texan is very short, machined for pellets, not slugs, which is rather silly, considering the .308 is a slug shooter.... I designed some slugs for Texans for NOE, with a smaller...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |