Titan ReloadingMidSouth Shooters SupplyLoad DataReloading Everything
Inline FabricationLee PrecisionRotoMetals2Wideners
Repackbox

Search:

Type: Posts; User: harkom

Results 1 to 24 of 24

Search: Search took 0.00 seconds.

  1. Replies
    19
    Views
    2,448

    Forum: Shot Guns

    Bill*B ....Is that a Federal 209 primer in your...

    Bill*B ....Is that a Federal 209 primer in your posted receipt?
  2. Replies
    25
    Views
    2,149

    It would be useful to know the specific Federal...

    It would be useful to know the specific Federal hull you refer to. Is that the Gold Medal?
  3. Replies
    4
    Views
    1,672

    Old alliant / hercules loading manuals

    Hello.
    Can anybody point me to an online source for previous editions of Alliant loading data?
    Thank you for any help and apologies if this information is already on CastBoolits.
    harkom
  4. Replies
    10
    Views
    2,573

    Take note that the CCI 157 primer has a covered...

    Take note that the CCI 157 primer has a covered flash hole, whereas the Remington 57 has open flash hole. Ball powder should not be used with latter type.
  5. Forum: Shot Guns

    Thank you for the clarification on this point....

    Thank you for the clarification on this point.
    Previously I had assumed the "stack height" to mean the combined powder, wad(s) and shot column - the optimal total height supposedly being that which...
  6. Forum: Shot Guns

    Cap'n could you define exactly "the stack...

    Cap'n could you define exactly "the stack height"? Measured from the base wad uppermost surface, ,,,or the upper surface of powder, or op card - to underside of- or topside- of shot?
  7. Thread: 10 gauge loads.

    by harkom
    Replies
    25
    Views
    3,599

    Forum: Shot Guns

    As the man says, but I would probably use FFG if...

    As the man says, but I would probably use FFG if available.
  8. Replies
    23
    Views
    2,099

    Forum: Shot Guns

    Polyurethane varnish/nail polish applied to top...

    Polyurethane varnish/nail polish applied to top card and case mouth inner wall helps with moisture control but is not truly waterproof. A plastic overshot card plus varnish would pretty much form a...
  9. Replies
    20
    Views
    2,475

    Forum: Shot Guns

    I think that the flat edge RTO would have been...

    I think that the flat edge RTO would have been applied to reloading used paper case hulls to give a stronger closure. The paper at the case mouth tends to delaminate as well as getting weakened as a...
  10. Replies
    11
    Views
    1,688

    Just be aware that hulls which have a skived...

    Just be aware that hulls which have a skived mouth can present a slight problem in achieving a tight RTO as the thin wall may dimple or deform in when applying pressure, particularly if the plastic...
  11. Replies
    13
    Views
    1,765

    Forum: Shot Guns

    The comments regarding insufficient pressure...

    The comments regarding insufficient pressure appertain however the Fiocchi hulls primer chamber may be oversize for typical US 209 primers ie a loose fit contributing to the result.
    It would be of...
  12. Replies
    20
    Views
    2,475

    Forum: Shot Guns

    BGI made a hand RTO tool as per your post. The...

    BGI made a hand RTO tool as per your post. The RTO head was reversible - one side for flat and one for round edge RTO. The pins contained in the head have a flat edge to contact the hull mouth - for...
  13. Replies
    11
    Views
    1,688

    Length of free tube desirable to make RTO depends...

    Length of free tube desirable to make RTO depends to some extent if you are loading slug or birdshot. Paper hull requires slightly more free tube than plastic. Paper hull should not really be longer...
  14. Replies
    16
    Views
    2,266

    Hi 15meter I would be grateful if you could email...

    Hi 15meter I would be grateful if you could email me with a copy of that Alcan manual.

    harm
  15. Replies
    16
    Views
    2,266

    The Rem SP hull above is the old style with a...

    The Rem SP hull above is the old style with a fibrous composition basewad and a smaller primer socket than current 209 primer size. There was a Rem 57, a CCI 157 & Alcan G57F - the last one being...
  16. Replies
    14
    Views
    1,569

    Plastic wads on top of BP will cause a lot of...

    Plastic wads on top of BP will cause a lot of plastic residue to line the barrel, so make sure to clean the bore well afterwards.
    Top wads can be sealed well in brass cases with silicon sealants -...
  17. LRR01 - I am asking myself just exactly what...

    LRR01 - I am asking myself just exactly what blackpowder load would require the level of accuracy in volume that this Hollywood measure may deliver. And does it's degree of accuracy vary depending on...
  18. Replies
    33
    Views
    3,994

    I have used a Redding No2 for 25 years. Excellent...

    I have used a Redding No2 for 25 years. Excellent build (US manufacture), reliable, virtually failsafe. Cannot vouchsafe the new ones of ?foreign manufacture.
  19. Replies
    6
    Views
    807

    Thank you Ken. I am looking for a primer...

    Thank you Ken. I am looking for a primer post/seating component and not the primer punch/knock out unit.
    Appreciate your comment.
    Neil.
  20. Replies
    6
    Views
    807

    thank you. will do.

    thank you. will do.
  21. Replies
    6
    Views
    807

    thanks for that. I had hopes that this site might...

    thanks for that. I had hopes that this site might get a result without going the evilbay route !
  22. Replies
    6
    Views
    807

    Lyman All American primer seating post.

    Hello.
    Can anyone direct me to a source where I may find a 209 primer type seating post for a LAA loading press?
    harkom.
  23. Replies
    67
    Views
    19,777

    Can anyone tell me if tooling was produced for...

    Can anyone tell me if tooling was produced for the Senior Turret press to reload 10G or 16G shotshells?
  24. Replies
    114
    Views
    25,431

    Unfortunately there is no mention of powder...

    Unfortunately there is no mention of powder formulation ( ie "ball" powder, granular or flake ) nor the type of primer ( ie sealed or open/unsealed flash hole ) - such information might provide a...
Results 1 to 24 of 24
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check