Titan ReloadingLee PrecisionReloading EverythingWideners
Load DataInline FabricationRepackboxPBcastco
RotoMetals2 MidSouth Shooters Supply

Search:

Type: Posts; User: EMT480

Results 1 to 19 of 19

Search: Search took 0.00 seconds.

  1. Replies
    21
    Views
    599

    I use the rcbs neck turner in a second case...

    I use the rcbs neck turner in a second case trimmer with a .17 cal pilot/cutter. Does ID and OD at the same time

    Sent from my SM-N970U using Tapatalk
  2. Replies
    21
    Views
    599

    After I cut the case length down. (Still longer...

    After I cut the case length down. (Still longer than final length) I turn the necks on each case. I have a second trimmer dedicated to this process. Don't have to constantly swap stuff around.
    ...
  3. Replies
    21
    Views
    599

    Not to sound like a wise guy, why trim first? ...

    Not to sound like a wise guy, why trim first?

    Sent from my SM-N970U using Tapatalk
  4. Replies
    21
    Views
    599

    I've had good luck with imperial. It's all I use...

    I've had good luck with imperial. It's all I use anymore for the majority of my stuff. If I fire up my Dillon. I use the Dillon spray lube.

    Sent from my SM-N970U using Tapatalk
  5. Replies
    21
    Views
    599

    Thanks for all the tips and tricks you guys have...

    Thanks for all the tips and tricks you guys have provided. Not having a 221 rem I did not have those dies. Just so happens there was a gun show today and i grabbed some. This is what I tried and...
  6. Replies
    21
    Views
    599

    I do recall after annealing first and then sizing...

    I do recall after annealing first and then sizing i crumpled the case good and decided that is not the way! I thought after I FL sized the 223 I ran it through the 221 die cut almost to length neck...
  7. Replies
    21
    Views
    599

    That is very similar to the process I used...

    That is very similar to the process I used previously. I didn't have the fancy dies until recently. I just can't remember to save my bacon what I did. Annealing and neck turning was in there...
  8. Replies
    831
    Views
    248,212

    Poll: 1 RCBS Jr. My everyday go to press 1 RCBS...

    1 RCBS Jr. My everyday go to press

    1 RCBS Ammomaster.

    1 Dillon XL 650

    1 Lyman Turret

    1 Hollywood SR
  9. Replies
    21
    Views
    599

    Collapsing at the shoulder. No they have not...

    Collapsing at the shoulder. No they have not been annealed yet.

    Sent from my SM-N970U using Tapatalk
  10. Replies
    21
    Views
    599

    17 fireball from .223

    Would love to hear from some case forming gurus. I had a simple process for forming 17 fireball from 223. I cannot for the life of me remember what I did. My guru mentor is no longer with us. I...
  11. Replies
    4
    Views
    413

    Forum: Gas Checks

    Thank you Sent from my SM-N970U using...

    Thank you


    Sent from my SM-N970U using Tapatalk
  12. Replies
    4
    Views
    413

    Forum: Gas Checks

    What recommendations for hardness? I see dead...

    What recommendations for hardness? I see dead soft half hard full hard

    Sent from my SM-N970U using Tapatalk
  13. Replies
    4
    Views
    413

    Forum: Gas Checks

    Question about making gas checks

    I recently ordered a Pat Marlins gas check maker. I assume he is still doing them. Got a confirmation email. Does anyone know his lead time? Where is a good place to source copper sheet?


    ...
  14. Replies
    4
    Views
    1,415

    Forum: Gas Checks

    What I ended up doing is tapering the entry of...

    What I ended up doing is tapering the entry of the die and polishing it a little more than I had done previously. Works like a champ now. Thank you for the comments.

    Sent from my SM-N970U using...
  15. Replies
    4
    Views
    1,415

    Forum: Gas Checks

    Gator Gas Check Problem

    I have some gator gas checks that are supposed to be for the .348 Win. I have an accurate bulled mold for casting .348 gas check boolits. The gas checks fit the shank properly. The problem I am...
  16. Replies
    2,540
    Views
    1,796,268

    Sticky: About time to build another...

    About time to build another...
  17. Replies
    13
    Views
    2,003

    Any idea where I could find the swaging dies? ...

    Any idea where I could find the swaging dies?

    Sent from my SM-N950U using Tapatalk
  18. Replies
    13
    Views
    2,003

    Yes it does have an additional 7/8 14 hole on...

    Yes it does have an additional 7/8 14 hole on top. What is the purpose of the extra hole? Thanks everyone for the info. Would this be an adequate press for swaging?

    Sent from my SM-N950U using...
  19. Replies
    13
    Views
    2,003

    Help identifying a Hollywood press

    Are there any gurus here than can help identify this...
Results 1 to 19 of 19
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check