Please add me to the list 1 BRASS three cavity plane base hp mold huntnman at swbell dot net.
Type: Posts; User: huntnman
Forum: GB RUN BY 2 dogs
Please add me to the list 1 BRASS three cavity plane base hp mold huntnman at swbell dot net.
Forum: Reloading Equipment
Would like to follow thread, have interest.
Forum: Completed Deals
Will take 380,30/06,44, Dillon dies. Greg<huntnman
Forum: Completed Deals
If not too late i could use a blue five pack also.
Forum: Lead and Lead Alloys
It looks like your regulater is adjustable lower the preshure. Air in take is adjustable too, losen the two screws turn silver disk to adjust. If flame doesent respond to lowering or raising...
Forum: CB Loads / Military Rifles
Yes it could. Reduced loads could reduce pressher and velosity. If there isnt enough velosity the projectile, may not stabilize, rate of twist and weight of projectile pending.
Forum: Reloading Equipment
One of the first things i did. Looked to make sure if I could see any damge to surfaces. to my inexperianced eyes all looked good, but I did have an small object (small roll of electrical tape) fall...
Forum: Reloading Equipment
+ My scale is like many have previously stated giving different readings of the same charge. the same three grain charge may read 2.8 - 3.2 grains. I now do not trust it. Can not get zero to be...
Forum: Reloading Equipment
I have one I would love to have repaired.
Forum: Casting Equipment
Sizing sink I believe would be very hard to do. Would love to see it done. I cant cut sink wheelweight with a large nine inch side cutter.
YMMV Greg<huntnman
Forum: Cast Boolits
I'm suspicious that the mold is not mating correctly the parting lines don't look correct.
Willowbend ^^^ A+++ Supper guy to deal with. 8/23/21 Greg<huntnman
Forum: Completed Deals
will take per our PM. PM on way Greg,huntnman
Forum: Helping Hands
Picked up mine I found it on the front porch today. Happy Happy Happy. I was worried I might of been the victim of the lost and stolen delivery system. Yes I maybe a pessimist. Anything good can turn...
Forum: Helping Hands
I could use that greenish rainbow on my RCBS supreme press. thanks for the offer.
Forum: Cast Boolits
What I see is your mold halves are not in alignment. .003 off in your drawing. Bottom shifted to the right top shifted to the left. The parting line on the boolit shows one side of drive band sized...
Forum: Cast Boolits
Washer on top of sprue plate concave up towards head of the screw.
Screw head
washer bubble up
...
Forum: Casting Equipment
1 Depends on the heat output (BTU) of your burner., probably .
A wind screen may help, you need to concentrate heat to the mass, stand, pot and contents. The first 1" ALWAYS takes the longest.
...
Forum: Casting Equipment
Sounds like your burner might not produce enough heat. When melting lead the first 1" always takes longer. You have to get every thing up to melt temp. Skim and flux once all is melted. There is a...
Forum: Casting Equipment
Gorilla Glue works for me. If they do come lose its a quick fix. I have a set of handles for most of my regular use molds. the ones I have glued on have held up well.
Forum: Completed Deals
Ill take these pm on its way. slow typing
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |