Search:

I used to get .625 hard cast R.B. from turbo1889 he disappeared in 2014 (hope he is alright) any other place to get them?
Thanks Roy

Loaded 10 of the load above shot 7 at a target at 25 yards free hand group was less than 4" but 4 slugs where touching in one bunch 3 in the other bunch were touching. if split into 2 seperate...

mold and new lead pot arrived today load 10 of these loads once I tighten the bolt on the pivot of the mold it worked fine didn't have time to get out to test them
Roy

I have a 1 oz mold on order. I want a mild load my lee loader is set up to drop 17.2 grains of clays which is a listed 1 oz shot load
From Hodgdon data
Lead Shot 12 1 oz. Clays Win. 209 ...

9mm case, drop of flux, 60 grains of lead shot heat till lead melted and bonded to brass ( to get weight to 1/4 oz) paper patched the cases with sketching paper made cork wads and hard card...

How well do the the lee keydrive slugs shoot in a smoothbore ? cylinder bore gun? modified choke ? 50-60 yards max? I searched for a while and found no good answer
I was given 280 lbs of lead ...

We have done banned those at our gun club the average person is over the backstop by the 3rd or 4th shot

that's why I worked up the load [smilie=s:

The tracker II is rifled the older tracker is smoothbore both are standard weight I am shooting the above load in a Rifled gun I do have a 1977 vintage H&R buck smoothbore in route
Roy

I can shoot 4" groups at 100 yards with iron sights and my bad eyes My slug target is a 9 inch paper plate with a 2 inch black circle in the center. If I hold on the center black circle at 25...

I have some hard cast round balls 20ga .625dia. made by turbo 1889 here on the forum. I load in B.P.I. 3" multihulls I use bluedot powder, gas seal over powder, nitro card, 2-1/2in hard waxed...

No In the winter months our club closes at 5 pm . I get home at 4;30 and it is 20 munites to the club . May not get out this week end we have a weather advisery this week end

The ones I'm playing with weighed for average with a .5 scoop out of my lee dipper set of 7 1/2 shot they are weighing between 105-110 grains about the same as a 1/4 oz slug loaded head toward...

the first post here gave me the idea I know 15 grains of h110 is a load given to me for 3/4 oz 410 shot load( by the manufacturer of the powdwer) so it should be safe for a 1/4 oz load. the brass...

25 yards 4 shots
http://i203.photobucket.com/albums/aa32/plumberroy/P2050215.jpg

you just had to post this :mrgreen got me thinking ....and experimenting I have been using the cut off wad home made cork filler wads a leather wad under the hull and today I got'em to group paper...

B.P.I. multi hull 3"
winchester 209 primer
27 grains bluedot
B.P.I. gas seal
nitro card
2 1/2" hard wax cards
B.P.I. 1/4" felt wad
.625 hard cast round ball
roll crimp
2 1/2 groups @...

Bingo You should have to work in the field in your specialty under a jouneyman for at 2 years before being allowed to engineer anything!!!!

Do you know the difference between an engineer's boots...

Reloader3006 is hooking me up [smilie=w:

Thanks Reloader3006

If this is not allowed please delete.
I need a box or two 2 3/4 20 ga paper hulls where might one find these?

I got some .625 round balls off of Turbo1889 and got around to trying them today . My load started at
B.P.I. 3" multi hull preprimed
24 grains of blue dot
gas seal
nito card
2- 1/2 hard...

Hi Chistof
Since I carry one of you knives around. I have no doubt in your metal working skills. I have handed a 20 gauge roll crimper to some of the best tool and die makers in the auto industry...

no, I'm just shocked on how much they were going for on evilbay. I have a lee 12 ga press but every thing else I load with these mainly 10ga 20ga slugs and 28 ga I might trade the extra 12 ga...

After mentioning these in the 28 ga round ball thread I looked on ebay at what these are going for :holysheep $110 for a ten ga $75-85 for 410-28ga $50-$65 for 20, 16 or 12 gauges
I have them...