Hey,, hc18flyer,, is that the NOE .360 232 RF GC mold that you have ?? i was just over on the NOE site and thats the only 35 that realy fits the bullet you described,,, also says it's the mold for...
Type: Posts; User: rammbler
Forum: Lead and Lead Alloys
Hey,, hc18flyer,, is that the NOE .360 232 RF GC mold that you have ?? i was just over on the NOE site and thats the only 35 that realy fits the bullet you described,,, also says it's the mold for...
Forum: Lead and Lead Alloys
Thanks Guys,, i found some of the threads on drilling the flash holes,, looks like a # 29 bit does it,, the reason for the heavy sub sonic an near to it was i was trying to duplicate the .350 lgnd...
Forum: Lead and Lead Alloys
Hello Guys,, been doing more range work.. so , the 38.4 gr lever w/ rcbs 35 200's is giving a solid 2050's out of my 22 in barrel,, tried 2400 with the same boolit,, 17 gr is pushing it 1602 fps,,...
Forum: Lead and Lead Alloys
Thanks Larry,, my original start up load was 42 gr of lever,, i was sizing .360 , had 3 coats of Hi-Tek coating baked on them,, when i checked the load with my chrony they went over at 2198 fps,, i...
Forum: Lead and Lead Alloys
Hello, i had the chance to pull them down,, the cases show no signs of pressure and the primers show a little flattning but almost no mushroom ,, all in all ,, this load would work but i think i'll...
Forum: Lead and Lead Alloys
Hello,, finely got a chance to run a few over the chrony,, rcbs 35 200 in once fired R P brass, alloy is 18 hbn majic alloy from missouri bullet, [ 92-6-2 ] using cci 200 primers and gas checked,, i...
Forum: Lead and Lead Alloys
Thanks guy's,, i realy like this old model 14,, my .359 dies came in today,, i'm going to try it without the lube,, the rcbs 200's seemed to run alright,, the montana bullet works saeco # 352 at 245...
Forum: Lead and Lead Alloys
Hello,, i'm hoping to find someone a whole lot smarter than me to help me figure this out... i'm shooting a 1914 made rem model 14 in 35 rem,, casting the rcbs 35 200 ,, .360 sizer is sizing .3595.....
Forum: Frequently Asked Questions
Thanks Jim,, i was kind of concernd about the shallow grooves in this H&R,,the older rifle bores were a bit oversize and this mold throws an under sized tapered bullet,, that if i under stand...
Forum: Frequently Asked Questions
Hi,, this is my first post/question,, hope someone can answer this. i picked up an Ideal mold/ tong tool for my W&H [ H&R ] 38-55 target rifle,, it's casting a 240 gr taper boolit,, first band in...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |