Search:

I like Lyman's 452460 for .45 ACP, and RCBS 45 270 SAA for my .45 Colt Blackhawk. I also use a lot of the RCBS 250 grain rnfp in the Colt. hc18flyer

I get a little conflicted here? I am a long time Class A CDL holder. I am also an active volunteer EMT with my community. Several years ago I responded to a truck accident on a rural highway, the...

Glad you are back Char-Gar! Missed your contributions! hc18flyer

Check on a new thread in 'Lead and Lead Alloys'. hc18flyer

Thanks for the suggestions. I will have to add to my 'wish list'! I may try to make up a simple stand? hc18flyer

A few weeks ago I borrowed a friend's micrometer to check my Dillon powder thru expander. I ended up ordering a new one for my button nose wad cutters in .38 Special. I found my 'cheaper' digital...

Great news Murf! I had a prostatectomy about 12 years ago, appears the doc was able to get it all? I have a family history of it, a nurse noticed my PSA numbers had doubled in a year, still...

I wanted to powder coat some 358156 gas check bullets, but I wanted the checks on first. I put the checks on and ran them thru a Lee sizing die, then applied pc with 'shake and bake', using 'Smokes'...

I try not to handle bullets any more than necessary with my bare fingers, have occasionally used a nitrile glove. I use the 'shake and bake' method, and and have not needed to clean bullets prior to...

I have mostly used gas checks. I have since started powder coating, but haven't tried pc with plain base bullets yet. hc18flyer

My favorite 8 mms mold is an Accurate 33-205T, shoots GREAT in my Yugo M48. Flat nose hits hard on whitetail too. I have NOE 325470 or 471 too. My brothers Yugo has a smaller throat and loves the...

Forster had some 'seconds available? There are different versions, some allow the press to 'cam over'? I don't have a set yet, but think I will soon?

Sorry to hear that! The highway is a very dangerous place for cops and first responders! RIP Christina.

2TM101- Wooden ramrod aren't inherently dangerous, they 'can be', if chosen, made, or used incorrectly. I use both plastic and wooden range rods, at camp or range. I prefer hickory, but oak can work...

Ditto! Brass molds are heavy, but man do they cast nice boolets! I do use the synthetic oil that came with my NOE molds and a cotton swab. hc18flyer

I have read about the Merit aperture device. But I also read about the 'stick on magnifiers? Tom

I am trying to remember where I read about using a 'stick on magnifier, that allows you to see your front sight? My 65 year old eyes don't focus well any more. I have been following this thread, and...

I have a Henry single shot .357 Mag, reamed to Maximum, love it! A friend had a Remington pump .22, always liked it. If Henry offered a .357 pump, I'd find a way to get one! Course my 12 gauge 870...

I would use 'Bumpo's alloy calculator on this Forum to form an alloy close to 'Hardball' and get to it. I powder coat, so I would use 97% lead, 1.5% each of antimony and tin. Hardball has closer to...

I segregated my components as I aquired them. I have coww, soww, linotype, and pure lead. I have purchased pewter and solder. I have utilized the alloy calculator from 'bumpo', from this Forum. I...

You had better buy a lottery ticket today, you're golden!

Sorry for your loss. I am looking forward to getting one again, been missing my Brit Spaniel Lucy for a while now! hc18flyer

NOE has 'in stock' molds off 20%. I am fighting the urge to buy another! Maybe I could sell a couple to justify it, huuuum? Many things are considered a 'disease', boolet casting surely qualifies!...

Loaded 200- .38 Special button nose wad cutters on my Dillon SDB, using the Photo Escape .358 HTC 'powder thru expander'. I loaded them over 2.5 grains of Clays. Last week I loaded a few at 2.7...

Be cautious with any CBD product, you may not be sure what you have? I serve as a volunteer EMT, with our ambulance service. Recently I had a patient that took " a couple" of gummies, ended up...