I think the issue with pewter is you really dont know what the composition is so the mixing chart is only a guide. Ifs pure tin, which it is not, then 16-1 would get you about 11-12bhn. Adding more...
Type: Posts; User: fredj338
Forum: Lead and Lead Alloys
I think the issue with pewter is you really dont know what the composition is so the mixing chart is only a guide. Ifs pure tin, which it is not, then 16-1 would get you about 11-12bhn. Adding more...
Forum: Cast Boolits
Not to mention over taper crimping. I've seen 0.357" bullets go in & then pulled to measure 0.354". Yes likely to lead even with PC or at least tumble.
Forum: Cast Boolits
Well not true really. Run an unlubed bullet down the bore & tell me how much it doesnt lead.
Forum: Cast Boolits
I think soft lubes do better with leading than hard lubes. I have moved to PC to just eliminate the issue & the smoke. I size 0.357 to fit any 9mm I have. Generally clip ww alone work fine at 9mm...
Forum: Lead and Lead Alloys
Only time I add tin is making LHP. I use 20-1 for bullets up to 1200fps or so in my handguns.
Forum: Cast Boolits
I have had the gc taken off several pistol molds. Its just not needed imo with PC today. I can run 125gr @ 1400fps in 357 or 250gr @ 1400 in 44mag & anything under that without leading & good...
Forum: Lead and Lead Alloys
IF pure lead & verified lino, I find 4-1 works just fine, especially if you PC.
Forum: Cast Boolits
Pure lead could work in low pressure rds like 38sp & 45acp but accuracy may suffer on shallow semiauto bbls. Just have to try it. Even a small amount of tin, desirable for getting good molds fill...
Forum: Cast Boolits
The Lee 147 is a very good bullet & my 6cav puts a lot of them out pretty quickly. I only PC. I also have a Saeco #910 4cav that is my go to for competition. the RN is just belt & suspenders.
Forum: Cast Boolits
Use a larger than needed bore brush. Fill the chamber with Kroil ^ let it sit a bit.
Forum: Cast Boolits
Clip ww have always been a bit vague. Stick ons almost always pure lead. Exact composition really isnt required, just work with bhn. Cast a couple & test them then add alloy to harden as needed.
Forum: Lead and Lead Alloys
My buddy is a welder & made me a smelting pot out of a 10" dia section of steel pipe, pour spout on the bottom & threaded rod to close off the spout. It works great but I only do about 60# at a time....
Forum: Cast Boolits
No diff than casting for any handgun caliber. I like the Lee 175TC. I size 0.401" after PC.
Forum: Cast Boolits
A proper taper crimp just removes the flare. If you are taper crimping enough to prevent setback, you are deforming the bullet. Neck tension prevents setback, not taper crimp.
Forum: Cast Boolits
You know that WST is inverse temp sensitive. So be careful working up loads in the heat & then shooting in freezing temps.
Forum: Cast Boolits
I load for everything though very little shotgun, just not worth it. They are all diff but the same. Pistol is easier, but more steps. you'll be fine if you have already done rifle.
Forum: Lead and Lead Alloys
IF it wont melt, I would say zinc. I would think any non zinc alloy is going to melt above 700deg. maybe a Babbitt?
Forum: Cast Boolits
Yes it will but easy fix, ditch the lube & use coated lead.
Forum: Lead and Lead Alloys
If your range has a plate rack bay, that is where you can get a lot of 95% useable alloy. Just pick up the flattened bullets, jackets are usually gone.
Forum: Cast Boolits
My buddy sprays but seems like a lot of wasted PC & you have to stand the bullets up to spray & of course, exposed lead bases. I do fine shake & bake. Drop them nose first in 150rd ammo tray & invert...
Forum: Cast Boolits
Yet it is area specific. I see shortages in grocery stores in Atlanta area I dont see out here.
Forum: Cast Boolits
Its the darling for many competition shooters. I like it but cost is pretty high & availability was always spotty. Its faster than Unique, meters well, flash suppressed, a very good service caliber...
Forum: Cast Boolits
Everything about Kalif is infringement on 2A rights. I have been here for decades & seen it go from bad to worse to almost unworkable. I retire this year, & hope to be gone soon after. Newscum can...
Forum: Lead and Lead Alloys
My buddy gets free lead sheeting, a couple tons of it. So i now have access to it for free thru trading.
Forum: Cast Boolits
Try a tray covered in parchment or non stick foil. Not sure how the comm guys do it in volume.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |