Well that’s pretty interesting, with the 44.8k psi, since that specific load came right from Hornady’s published data- 1.060 OAL, Unique @ 5.0gr. I thought the pmax for 9mm was 35k psi. Any idea why...
Type: Posts; User: tinhorn97062
Well that’s pretty interesting, with the 44.8k psi, since that specific load came right from Hornady’s published data- 1.060 OAL, Unique @ 5.0gr. I thought the pmax for 9mm was 35k psi. Any idea why...
Can anybody run a couple loads for me through Quickload software? I’m interested in seeing the predicted change in pressure/velocity as the OAL changes. Below are the inputs:
9mm mixed brass...
Well I cut the petals off of a AA12R wad for a check fit, and those .323 diameter pellets sure stack nicely in 3’s inside of a blue Peters hull. My cast .350’s fit better as well, stacked in 2’s.
...
Well as luck would have it, somebody in S&S just happened to be selling a .311 mold- so I grabbed it just now. Thanks for the recommendation!
Sent from my iPhone using Tapatalk
Hey folks. This may be a “dumb question”, but I’ll ask anyway.
I have AA12, AA12R, and HCD-18 wads. Looking at load data, I see 9 pellet, 10 pellet, 12 pellet…but I can only get 8 to fit inside...
Well since starting this thread, I have purchased the Lyman shotgun reloading book and, from BPI, both the Cheddite and Buckshot manual.
After doing a short initial look through each of them, I...
I don’t mind buying the books, just was a little lost of which books would be deemed necessary for the loads that I’m planning to make. Sounds like I should order the Lyman manual and BPI manual(s)...
Thank you so much for that wealth of information. A couple take always for me are: 1) buy the various manuals, and 2) it’s probably best to just stick with one set of components and find what works...
Hey folks,
I was just looking at BPI’s selection of manuals and see a Cheddite manual, a Buckshot manual, a Slug manual…
Is there a good “one stop shop” for load data for slugs AND buckshot? I...
Ya’ll are awesome. I very much appreciate the help.
Sent from my iPhone using Tapatalk
Hey folks,
I just dropped the hammer on a purchase to get tooled up for loading 12ga. In the pile of goodies is a roll crimping tool. I spent some time educating myself on the usage of a roll...
Forum: Shot Guns
That’s good to hear. I am also a fan of the 870, but a couple things caused me to go a different direction: price point and the recent (last few years) quality woes with Remington.
I had a...
Forum: Shot Guns
Hey folks. I am in the market for a good pump 12ga. I would love to buy used on the private market, but I happen to have a $500 cabelas gift card- so that’s the route that I’m going.
I would like...
Forum: Our Town
I’ll try to keep this fairly short and simple.
For those seeking pain relief, CBD by itself really isn’t going to do a lot, because CBD is designed to work in conjunction with THC and the myriad...
Forum: Our Chapel
Update:
She’s out of surgery, awake from the anesthesia, and resting for the night. They were able to get the vast majority of the growth off of her spine. They also have her blood pressure...
Forum: Our Chapel
She is currently in surgery at OHSU in Portland, OR. She has a calcified growth on her spine that has been causing mobility loss, and they’re currently trying to decide if they can safely remove it...
Forum: Helping Hands
it’s an older RCBS set with the knurled lock ring on them.
Sent from my iPhone using Tapatalk
Forum: Helping Hands
These dies are older...probably late ‘70’s vintage. By the sounds of it, that assembly will likely work.
Sent from my iPhone using Tapatalk
Forum: Helping Hands
Hey folks,
I’m trying to help a neighbor get tooled up for .44 Special. I’ve acquired most of what is needed, but I’m lacking the decapping assembly for a .44 Special sizing die.
I either...
Forum: Cast Boolits
Same. Incredibly accurate, very good penetration, and happens to be my “carry load” over 5gr of Unique. I don’t feel under gunned with this load whatsoever.
Forum: Our Town
Well, I’m going to jump in here also. I’m located in SoCal, and would be happy to help a person get going. I’m a big fan of keeping things simple, and I’m also a big fan of sharing knowledge with...
Forum: Our Town
Unless I’m reading it wrong, you seem to be correct in this statement.
ATF Federal Explosives Regs, Ch 40, Sec 842, paragraph (p): to paraphrase: “it’s unlawful to share information about how to...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |