I am definitely willing to add. I looked at you pics but not exactly sure what you have going on. looks like a square tube mount that can adjust height?
Type: Posts; User: TylerR
Forum: 3D PRINTED RELATED ITEMS
I am definitely willing to add. I looked at you pics but not exactly sure what you have going on. looks like a square tube mount that can adjust height?
Forum: 3D PRINTED RELATED ITEMS
If you have any change suggestions feel free to email me. I don't want to re-write the thing but I am always open to tweaks here and there.
Forum: 3D PRINTED RELATED ITEMS
It is just in MS Word. I have it and do make tweaks from time to time.
Forum: 3D PRINTED RELATED ITEMS
All very good points. I had considered using "Legacy" as well, and since you just threw it out there I will go with it. I think I will avoid moving them out of the folder for now, but very well...
Forum: 3D PRINTED RELATED ITEMS
FYI I renamed the entire Drop Tube's folder today. The versions designed for prox are the official latest version. They are now just labeled with the original file names. Drop_Tube_X and...
Forum: 3D PRINTED RELATED ITEMS
Don't worry about the Cura error. Yes there are some files that give that but they print just fine.
The file GWS posted is actually the latest (short) version.
I would also recommend you grab...
Forum: 3D PRINTED RELATED ITEMS
Honestly couldn't decide on where to put them. They ended up in the Main Body folder since that is where the drop hole adapters are, and the spacers are an extension to that. They could also go in...
Forum: 3D PRINTED RELATED ITEMS
See, I knew you would set me straight. The config makes sense, and could be used with stock parts, minus the spacer you are using. I added both the funnel and straight wall versions to github.
...
Forum: 3D PRINTED RELATED ITEMS
Not sure I am following GWS, could be because I am slow. The drop hole on the collator body is 16mm dia. If you attach the top adapter, it is going to go from a 16mm hole directly to a 10mm or 14mm...
Forum: 3D PRINTED RELATED ITEMS
I had the same question. If he is running a tube straight from the collator then the cone entry is the only answer for the top adapter. Otherwise it has to be some kind of offset adapter.
Forum: 3D PRINTED RELATED ITEMS
Nice. I have been snowblowing all day here.
Forum: 3D PRINTED RELATED ITEMS
Go to Adapters folder on github and check out the Lee_Tube_Adapters.
Forum: 3D PRINTED RELATED ITEMS
Give me till tomorrow. I will post something.
Forum: 3D PRINTED RELATED ITEMS
Use the APP_Drop_Tube_Adapters here:
https://github.com/BF556/Feeder/tree/main/8.%20APP
Forum: 3D PRINTED RELATED ITEMS
2A is enough to run the collator.
Forum: 3D PRINTED RELATED ITEMS
You have three options to choose from:
-Drive a pin directly thru the motor shaft.
-Use a hex adapter
-Use a hex adapter with a pin
Most people go with option two.
I use the last option. ...
Forum: 3D PRINTED RELATED ITEMS
Yes, everything is designed around the spring adapters. not direct to spring.
Forum: 3D PRINTED RELATED ITEMS
This is fairly well documented. There is an adapter to go from a drop tube to the Dillon case feed adapter. Going to need more detail on what you have tried to give a good answer....
Forum: 3D PRINTED RELATED ITEMS
I did just post a more recent version of the generator. v2.1.9. ton of new stuff in it but more complicated.
Forum: 3D PRINTED RELATED ITEMS
Did you make any changes to the settings? What sent over was my best guess. You could try increasing the rifleHoleWidth to 12
You can do all kinds of things with the ridges. Its all in the...
Forum: 3D PRINTED RELATED ITEMS
Easiset thing to do is to go to the example section and find the large rifle brass block of code. copy it, and replace what is in the "#### Customize Here ####" section. Then change what you need. ...
Forum: 3D PRINTED RELATED ITEMS
Was doing some loading last night and looking at the collator, and immediately it jumped out at me that the mount is typically at the back of the feeder. which is where the debris is going to...
Forum: 3D PRINTED RELATED ITEMS
I have considered the same. Would need a trap underneath to catch the debris. I will look at it.
Forum: 3D PRINTED RELATED ITEMS
Hey Ed! Haven't heard from you for a coons age. Hope all is well.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |