Search:

I can normally see a small amount of light around the pins on all of my RG molds, it's just the nature of machining tolerances and retaining the ability to open and close them freely. You need to...

Your best bet is to call, Al is great about picking up the phone especially early in the morning. Ask him if it's on the list of molds to be ran, which I would bet it is. The problem is the list is...

New mold day is the best, except for that dang break in period.. Very cool, I remember when this bullet was designed and didn't know you could buy the mold for it. My 1:7 barrel stabilizes the NOE...

Looks like the gator checks are in short supply at the moment, I normally get them through NOE, bayoubrassandammo.com or Sages Outdoors. Currently Sages appears to be the only one with them in stock....

https://noebulletmolds.com/site/product-category/bullet-moulds/338/htc339-315-fn-bz1/

I almost exclusively shoot coated cast in my 338 Spectre's with 1:6.5 twist. Mostly subsonic, no issue stabilizing 315gr down to 740 fps. I haven't done much with supers but 200gr checked and coated...

I've done quite a bit of back and forth with Taco regarding the 458 Socom and 338 Spectre over the last few years.

For the NOE HTC459-500-SP (PC and sized .4595") @ 2.18" with CCI 350s
Accurate...

I have been a fan of No. 5 for years but never tried it in 357 until now. Dad asked me about a medium power plinking load for range days.
I recently got the NOE HTC358-154-RF, got some powder...

Good information and great story telling. What part of South Carolina, I just started hog hunting this year in Kershaw county. Bagged one 200 pound boar and I was hooked, talk about good eating!
I...

https://web.archive.org/web/20120418083147/http://john-ross.net:80/loading.htm

Getting harder to locate the John Ross spreadsheet these days.. 700 grain is at the bottom with 7-8 powders listed.

Just my two cents here as I am in the same boat as you, I purchased my first PB checks last week. My first attempt was with bullets cast and powder coated a few months ago and I snapped a press in...

Using the NOE HTC 354 grain bullet I started with 28 grains of W296, yielded 1420 fps in my 10.5 barrel.

Check your bullet size, I ditched my Lee 175 grain mold for my G29 because it was dropping undersized at .399".

It is the same mold, unless they went back and fixed it since doing the group buy run. There was plenty of interest, the intent was to make it 168 grains but after cutting the molds the final product...

I'm not sure I qualify for "mentor" status but always willing to try to help, what area of upstate? I'm in Camden a little closer to the garnet area, takes me about an hour and a few to get to Fort...

Yessir, it was originally designed as a boat tail but due to demand in 300 blackout Al agreed to offer a plain base version as well.

http://noebulletmolds.com/NV/index.php?cPath=84_461

Also curious to see what you're shooting these from.

I have the 174 grain version and have been contemplating this mold, tuned in for results.

These HTC molds wreak havoc on your wallet....

Shdwlkr
First and foremost, thank you for your service.

Since I started shaving my head I've always had a beard to some degree, my face never fared well shaved smooth. I can handle a breeze on...

Hey now, hair on your head is no standard to measure age.. Mine started receding at 16 and the top began disappearing at 19. Early 20's I started shaving it bald and six years later I have never...

Appreciate the tip and I have been meaning to copy that setup since I saw it a while back. I'll need to get as much done as possible in the next six weeks, expecting our first little one come...

My testing with this bullet is fairly limited to just finding a good load based on primer signs and ejector swipes, but I shot some 2 days ago and think I have a good window for win296. My first...

I just started posting on this forum last night but have been an avid follower since before I cast my first bullet only a year and a half ago. I began reloading and casting at the age of 26. My...

I did not mention it in my original post but the 174gr I load for plinking supers. Like oger I also use the 247gr in plain base, again powder coated and sized .310 with no issues in slotted sheridan...

Tumble in a #5 container. Used to use bb's but pre heating the bullets before tumbling works just fine. Dump them on a wire mesh tray, bake for 10-15 minutes and quench in water bucket.

I bought this mold in plain base during the group buy. Shoots just fine in my 16" PSA upper, no problem sizing to .310 after powder coat.