It actually feeds well from pmags only
Type: Posts; User: thegasharkman
Forum: CB Loads / Military Rifles
I am loading these 247GN RN NOE with 9 grains of H110 for a suppressed 8.5" SBR AR15
Does anyone know the minimum powder charge. I don't have a chronograph to determine how far they are above the...
I have 55gn gas checked .223 cast bullets I got from a fellow member a few years back
I need a load data for h4895. I used to have it written down but my notebook was destroyed in a move. Thanks in...
Forum: Cast Boolits
Any on have any load data for loading cast 300AAC BLK Out Subs
Forum: Reloading Equipment
I have been hand loading .270 with nosler bst and using a lee die set. I have a rem 710 that has a 4rnd box mag. Sometimes they get thrown inside the brass when i shoot the round in the chamber. I...
Forum: Casting Equipment
The Kenjudo's setup?
Is there a detailed set of instructions to duplicate this pot?
Forum: Cast Boolits
what are the diameter specs on what yours are dropping at and do they have gas checks on them already?
Forum: Cast Boolits
I would like to know if anyone has seen where I can get a mold that will cast 180 gn .277 -.280?
You anyone comes across this and wants to sell a hand full of ogives that I can test fire and decide...
Forum: Cast Boolits
Has anyone here tried to cast these in .224 or 5.56 mm?
I am looking for at least a 75 gn round with a gas check so I can shoot slower rounds with out the wssm barrel burning out.
Please share what...
Forum: Boolit Lube !
show if this is the magama lube is this a good oops creation or a bad oops creation?
Forum: Boolit Lube !
Yeah I only shoot outdoors. I was just messing around when I made the batch. I intended to make a tumble lube and ended up with a pan lube. It seems to stick to the rounds very well. and everything...
Forum: Boolit Lube !
So I started out to make a variation of the Johnson's and Alox Tumble combination and ended up with a very hard high heat pan lube. My contents were Johnson's paste wax boiled to remove solvents,...
Forum: Cast Boolits
So i tried this with my latest batch of ingots. They were the best yet. Far better than wax or saw dust. This is a must for me!!!
Forum: Cast Boolits
57084What would you suggest for the charge. I found that load online but it was for a 125gn and now knowing that they are 133-136gn I have to find a new charge weight. The test fires were very heavy...
Forum: Cast Boolits
Do you have to size these bullets from this type mold? Also what lubing process are you using on the rifle bullets?
Forum: Cast Boolits
Nice I will def use this on my next batch
ok ill check the pot i bet it is sulfer. The lead I have been getting has a high sulfer content from the ground here. The smelting pot turns yellow on the outside when melting large batches. After...
Forum: Cast Boolits
yes that is way to high. I normally get them for 15 a bucket. I have been getting lead from a local range that pushes everything out of the back stops with a dozer for 10 a truckload. this usually is...
Forum: Cast Boolits
def a good question how did the lead turn out? I have tons of paper shreds if this is the easy source then I am g2g
Forum: Cast Boolits
Ok so the mold package says lee 124gn tumble lube lrn. It however only has 1 groove. I removed the bullet seater and ran the brass through and it fixed the bulge on the brass. I went and test fired 7...
Forum: Cast Boolits
OK I kinda figured just mess with it until it works. I also discovered the bases of the brass are ballooned, my friend that loads says this is caused by getting cases fired from a Glock. Is there a...
I have a 10LB Lee Production pot and I use it only for melting and pouring clean lead. I poured out the remaining lead and discovered that the bottom of the pot is rusting. What can be done to slow...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |