330574
There’s some 410 loads with charges under 1/2 ounce in the BPI small bore manual. Most are above average velocity.
I’m not optimistic the sub 1000 FPS loads will be significantly...
Type: Posts; User: Barry54
Forum: Shot Guns
330574
There’s some 410 loads with charges under 1/2 ounce in the BPI small bore manual. Most are above average velocity.
I’m not optimistic the sub 1000 FPS loads will be significantly...
Forum: Cast Boolits
Chilled shot is pretty soft. It is likely more valuable as shot if you could trade it.
Forum: Shot Guns
Thanks! That’s most helpful. I can work down from there when I get home.
My pump wouldn’t close on the 303 brass I have no use for. It might be time to dedicate some of the 444 brass for this task!...
Forum: Shot Guns
I just emailed BPI a request for help to their load of the week email address. Hopefully they will accept the challenge.
Forum: Shot Guns
That is pretty inspirational!
Do you have the courage to try it with a faster powder? I know you are a fan of TiteWad!
2 grains?
Forum: Shot Guns
For this application I would definitely put priority on low noise over power. Or a velocity requirement.
I am wanting something to dispatch critters when penetration of a fraction of an inch is...
Forum: Shot Guns
My initial concern is the airspace in 45 Colt recipes and no airspace in shot loads.
Knowing enough to be dangerous, I would assume the cushion section of shotgun wads mimics some airspace of...
Forum: Shot Guns
I subscribed to this thread. This specification would be great for rats and snakes and such. I’m sure it could be done with black powder, but I’d much prefer smokeless loads.
BPI takes requests...
Forum: Our Town
Another one bites the dust!
Momma always said “where there’s one, there’s more.”
How was the muzzle blast with your 444 short load?
Forum: Our Town
I’m sure the derringer is loud!
I’d love to have some 410 recipes with TiteWad or something fast. It would cut back the muzzle pressure and blast. Even if it was as light as 3/8 ounce or even...
Forum: Our Town
I wouldn’t want barn tin on the house even if it was new. Standing seam metal roofing would be better.
Forum: Our Town
I appreciate the opening paragraph of this thread. Thanks for nipping that in the bud!
Are your #9 loads 2-1/2 or are you using the full 3” ones?
The soil was dry and rock hard in Tennessee...
Forum: Our Town
http://poisonousplants.ansci.cornell.edu/yew.html
Japanese yew caused the death of several of our cattle when I was in elementary school. Looks like it affects goats too.
Forum: Our Town
May I ask what part of your new house is this sheet metal going to be used for?
Forum: Factory & Surplus Powder
I’m betting my money here as well.
Forum: Leverguns
https://en.m.wikipedia.org/wiki/James_Jordan_Buck
The Jordan buck was taken with a 25-20
I’ve learned there’s two kinds of dead deer. In the freezer dead, and lost in the briars buzzard feed...
Forum: Shot Guns
https://www.wkrn.com/news/local-news/williamson-county-woman-shot-in-target-practice-accident/
Found it.
Forum: Our Town
I remember radio station’s request lines back before you could pull up music on you tube.
Forum: Cast Boolits
You mentioned keeping costs down and shooting as much as possible.
The Lyman Gould’s mold is a single cavity hollow point mold. It’s a classic! 1800’s design.
But using a single cavity mold is...
Forum: Shot Guns
Getting back to the topic of the thread of a farm/house gun, it’s not a bad choice to pick a shotgun. New shooters and those less practiced might be able to hit the target easier with a shotgun than...
Forum: Cast Boolits
There’s a 12 gauge slug mold at a shop in St Charles MO missing the pin. Too bad it isn’t correct for it...
Forum: Cast Boolits
https://noebulletmolds.com/site/shop/bullet-moulds/458-460/460-315-rf-av3/460-315-rf-rg4-cavity-2gc-2pb/
330441
I don’t have a 45-70 anymore. My RG mold is for 45 acp and those are the ones I...
Forum: Cast Boolits
A round nose wouldn’t be my first choice to cast for hunting.
I like the NOE RG molds. It’s a “hollow point” mold that comes with three different pins. A flat point, cup point and a deep hollow...
Forum: Shot Guns
I was invited to dove hunt with a neighbor on the sheriff’s department. There was an impressive meal cooked on the Blackstone grill. His son in law said the blessing before we ate.
After the meal,...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |