Search:

Exactly the type of thing I was going to design for an endoscope display I have. Nice.

Sent from my Pixel 5 using Tapatalk

Also guilty as charged. Honestly how I stumbled upon the APP upgrades I didn't even see the manual, so that's my alibi.

Tyler does a really good job documenting things as I've learned through my...

I'm going to break down and print another base. I have enough stuff to make another minus motor and relay, so why the heck not I suppose. May even try out ASA. Have a decent profile worked up for it...

I sorta wondered the same, though I have a vibraprime that works well (and one that doesn't, probably need to tweak the tray some).

Sent from my Pixel 5 using Tapatalk

Print it, install it, and leave it there. Doesn't harm anything in my experience.

Sent from my Pixel 5 using Tapatalk

There is a plug to go into the one hole when collating brass.

Sent from my Pixel 5 using Tapatalk

I knew what ya meant. I haven't messed with silk much, though I do have some. I hear the prints aren't as strong as normal PLA but who knows. Been looking for printing motivation lately. Probably...

Polypropylene? Interesting. I print on PEI coated spring steel or glass. The glass carborundum bed was ok for a while but seemed to wear out as eventually I'd have a lot of adhesion issues.

I...

I've seen some black slides and jaws in the wild on youtube. Assuming it's a mixed bag from Lee.

Sent from my Pixel 5 using Tapatalk

These are the aftermarket APP slides you print yourself. In whatever color filament you have.

Sent from my Pixel 5 using Tapatalk

Yeah, I was new to ABL systems and somewhat new to 3d printing at the time I tried it. It may have been something I did. If I get another printer, I will try it. Though my next printer will likely...

I have an ezabl pro sitting around that I need to try again. Was getting repeatability issues, but I like the concept.

Sent from my Pixel 5 using Tapatalk

I would think the same commands as a CRTouch would work. I can't think of why one probe wouldn't have the same startup (though you may have different preferences regarding meshes, and depending on...

https://github.com/MSUICEMAN/Alternate-Locator-Buttons-for-Dillon

think i made a public repository correctly.

my laptop with a ryzen 7 3700, and 16GB ram, with an Nvidia radeon vega mobile Gfx (believe its shared memory) runs Fusion360 surprisingly well. ymmv though.

you are more than likely right on the shellplates. though i've loaded probably 20+k rounds on my 550 without issue, may also be cartridge specific. should work fine for locator buttons though.

I made STLs out of all the data I could find (plus some measurements of my own) for Dillon locator buttons. Can't find info for #6, but that is for Short or Super Short Mags, which I don't and...

For times sake... I'd probably fill that with JB weld, sand flush, prime and paint. Just be done with it.

Sent from my Pixel 5 using Tapatalk

That's exactly what I do, too. I have it up top, definitely for brass, but oftentimes for sizing bullets too.

Sent from my Pixel 5 using Tapatalk

I'm a tinkerer by nature. Plus I didn't know if I'd like 3d printing or not, so I ended up with two enders, one 3v2, one 3 pro. Both are heavily modded and upgraded at this point with new tubes, one...

Fancy shmancy! Fact is, I'm jealous of your printer. Wish I had advice about the switch, I went with the proximity switch option, and it just works when face to face with the flat of the drop tube. ...

Yes on Tapatalk

Sent from my Pixel 5 using Tapatalk

Back when bulletin forums were kinda clanky and common, I used Tapatalk because it was a one stop shop for nearly all your forums. Now the forum software is good, and I belong to less forums with...

I have a bookmark in my browser

Sent from my Pixel 5 using Tapatalk

Yeah, signatures don't show up on Tapatalk.

Sent from my Pixel 5 using Tapatalk