Search:

Cheap stands start at about $15 on amazon. That being said county gents advise about proper holding a mic aids in accuracy and proper feel.
...

0-1 Mics normally are zeroed by cleaning the anvil and the spindle face by pulling a clean piece of printer paper thru them. Gage pins close to the size of the part you are measuring ensures that...

I love quality tools. Most of my personal tools are high end. US made if possible. That being said some of the Chinese imports are 90% of the quality but 25% or less in cost. For low usage or...

If you go with Krieger you have several choices for rifling types. You also can pick your land/groove width. Standard is 30/70. Some claim for lead the 50/50 width gives the best accuracy. I have...

I am hoping for better. Manufacturing and machining Technologies have come a long way since the Contender was designed. Too the best of my knowledge Contenders never required the hand fitting some...

The old SAAMI spec for 45 Colt was .454". By the 70's most manufactures switched to .452" bores. The current SAAMI 45 Colt bore is .452". The current SAAMI 45 Colt bullet size is .456" -0.006". ...

Hopefully this will be good news.

https://www.gunsamerica.com/digest/gregg-ritz-acquires-thompson-center-arms/

Wabash, Indiana (April 30, 2024) – Gregg Ritz, a prominent figure in the outdoor...

I've never killed a coyote with the 223 and cast. I have killed a lot of coyotes. If you are looking to recover to sell or tan furs expansion is very desirable. In the 70's I shot dozens of a...

Unless you have an explosion venting storage safe storing BP in a safe is not a good idea. If you are storing guns any material that burns other than stocks is not a good idea but you can get by...

Looks like that one gets your attention when you pull the trigger? Very nice.

If cost is not an issue the technology is here. Printing aircraft turbine blades is a reality.
...

Krieger is my preferred. Greem Mountain is a little cheaper and have good reviews.

https://castboolits.gunloads.com/showthread.php?135651-357-Herrett-Case-forming

https://www.shootersforum.com/threads/forming-357-herrett-brass.189641/

Not aware of people claiming that the roll crimp is better for most applications of this type. Once the taper crimp came on the scene most prefer it. That being said lots of people claim that roll...

The Cannelure isn't correct for the M62A1 bullet.

https://www.ar15.com/forums/AR-15/7-62-NATO-M62A1-Tracer/16-729936/

https://www.amazon.com/butchers-bowling-alley-wax/s?k=butchers+bowling+alley+wax

The thermal expansion rate of aluminum for the common mold alloys like 6061, 2024 and 7075 are so close to each other that different aluminum alloys will not have a measurable effect on the bullet...

it pops up when you click on "selected messages"

check the box on the right side of the message than go to the bottom right side to selected messages than check the delete circle.

https://kirammo.com/the-ultimate-guide-to-understanding-colored-tips-on-ammunition/

Without seeing everyone's manufacturing process it's hard to make a blanket statement but on the one that I have seen the brass is produced in one area and yes it's the same brass for reloaders and...

This is still current.

https://castboolits.gunloads.com/showthread.php?330867-Lesson-learned-about-shippng-primed-brass

If this needs to be moved to the pit please do so. I cannot address your comments without some political overtones.

The 5.56 and 7.62x51 will still be the bulk of the rounds used in the...

I am using it now and it works great for me. https://cse.google.com/cse?cx=001951264366462437169:ggn3vg-bjum

? I stated it worked well. Now it's gone? I did save the link but others should find it useful also unless you don't want people using it?