Search:

I pre-ordered this printer and then proceeded to wait over two years for this to happen. Glad I finally made it :)


325522

Not sure if anyone has reported it already, but the "modified" link on page 16 under Step 8 (Part D) is broken in the manual.

I finally got my Prusa printer fixed (motherboard died) and now I'm off to printing new collator plates with clutches. Thanks TylerR as always for the hard work and also a huge shoutout to o416 for...

TylerR - Just a heads up your Contributors folder has two sets of files named similarly. One is just a "Copy of". Not sure if you meant to overwrite or not. I just wanted to make you aware to save...

The motor you linked works with the Main_Body_M634JS body. Thats the motor I use.

All of my jams thus far have only forced the set screw in my hex coupler out (and ripped a few threads out in the process). I think ruining hex couplers is preferable to ruining plates. That being...

Happy to report back that the new drop tubes fixed the issue for both sensors!

I'm happy to test any solution you think might provide an improvement. If you have a modified #8 tube let me know and I'll give it a whirl.

Thanks!

So I just tested the PRD18-14DN2 sensor and had the exact same issue as the uxcell 8mm. When the bullets are lining up in the tube, the part of the bullet that starts to taper ends up being right in...

Just to add a little more to this proximity sensor discussion. I've had 0 issues with 300BLK cases using the PRD18-14DN2 sensor and the #10 tube. However, last night I tried out the uxcell 8mm...

I'd worry about burning out the wall wart, but then again, I'm no expert.

I switched from the optical sensor to using the proximity. I never had any issues with the optical but much preferred the cleaner wiring from the proximity. I've also used both the PRD18-14DN2 (got...

My Brass_Slide_Adjuster has the same tension in the Brass_Slide_Plate no matter the orientation.

Something else I wanted to quickly report. I went to print the Brass_Drop_Hole_Adapter from version 1.3.5 and the orientation looked pretty strange from what I had printed last time so I went back...

So, I tried to just put a small dab of hot glue behind the slider and that actually worked great, at least for that problem. I decided that since 9mm cases arn't picky about the slider I'd decap a...

Not a bad idea. I might go this route if for no other reason to use up some of small rolls of filament I have. Thanks for the suggestion.

Hey everyone,

I just wanted to check to see if anyone would feel they'd benefit for a guide on how to add holes to the electronic box templates. I did it for the first time this weekend and it...

Do you have a rule of thumb for how much clearance to add?

Thanks!

Hey TylerR - When you're creating holes for connectors, how much tolerance do you leave? For example the 4 pin connector I have is is 12.5mm x 5.75mm. I assume making the holes exactly that size...

I finally got around to setting up the collator for case feeding the LNL AP. It seems to operate well in my limited testing. Next I plan on redoing the electronics box on the collator connected to...

Thank you sir! The reason I started with GWS' solution is because I felt like for cases I wanted the sensor closer to the collator so I have a longer queue given that it seemed from my very limited...

Ok, stupid question before I go printing/designing. My Lee tubes finally came in and I'm trying to determine the correct part to print to go from my 15.5mm OD spring to the 14.5mm OD Lee tube. I...

+1 on this. Although I do wish this website had SSL (https for the layman).

Thats the motor I use. Main_Body_M634JS.stl is what you're looking for.

I need to print another one anyways to reverse the threads to the spring. We'll see how it goes.