Yes. 1/8"x1"
Type: Posts; User: TylerR
Forum: 3D PRINTED RELATED ITEMS
You have three options to choose from:
-Drive a pin directly thru the motor shaft.
-Use a hex adapter
-Use a hex adapter with a pin
Most people go with option two.
I use the last option. ...
Forum: 3D PRINTED RELATED ITEMS
Yes, everything is designed around the spring adapters. not direct to spring.
Forum: 3D PRINTED RELATED ITEMS
This is fairly well documented. There is an adapter to go from a drop tube to the Dillon case feed adapter. Going to need more detail on what you have tried to give a good answer....
Forum: 3D PRINTED RELATED ITEMS
I did just post a more recent version of the generator. v2.1.9. ton of new stuff in it but more complicated.
Forum: 3D PRINTED RELATED ITEMS
Did you make any changes to the settings? What sent over was my best guess. You could try increasing the rifleHoleWidth to 12
You can do all kinds of things with the ridges. Its all in the...
Forum: 3D PRINTED RELATED ITEMS
Easiset thing to do is to go to the example section and find the large rifle brass block of code. copy it, and replace what is in the "#### Customize Here ####" section. Then change what you need. ...
Forum: 3D PRINTED RELATED ITEMS
Was doing some loading last night and looking at the collator, and immediately it jumped out at me that the mount is typically at the back of the feeder. which is where the debris is going to...
Forum: 3D PRINTED RELATED ITEMS
I have considered the same. Would need a trap underneath to catch the debris. I will look at it.
Forum: 3D PRINTED RELATED ITEMS
Hey Ed! Haven't heard from you for a coons age. Hope all is well.
Forum: 3D PRINTED RELATED ITEMS
I don't have a mirror setup. never found it that necessary so didn't set one up.
Forum: 3D PRINTED RELATED ITEMS
I think most people use a mirror. I have never bothered
Forum: 3D PRINTED RELATED ITEMS
You bet! General rule of thumb is the offset should be one step larger than the drop tube.
Forum: 3D PRINTED RELATED ITEMS
10mm drop tube, 11mm offset for both.
Forum: 3D PRINTED RELATED ITEMS
Haha! far from it. I just cover my mistakes well :)
Forum: 3D PRINTED RELATED ITEMS
That is good. The bearing placement relative to the die body is a big part of figuring these dies out. Would love to hear if the top hole works for the longer bullets.
Forum: 3D PRINTED RELATED ITEMS
OK, did you run a round file down it a couple of times to smooth it out? 6.5G spec says bullet dia is 6.71mm (.264) The insert diameter is 6.9mm in 3d CAD. Are the bullets you are using 6.71mm?
...
Forum: 3D PRINTED RELATED ITEMS
What exactly are you looking for.? Looking at the x-10 press, I would probably run a 1" tube up from the bench.
Forum: 3D PRINTED RELATED ITEMS
I have one designed but have no way to test it. I will post it to github if you want to give it a try and give me feedback.
...
Forum: 3D PRINTED RELATED ITEMS
Glad to hear you guys are making the most of it!
That may have been a mistake on my part. All of the alt drop tubes were recently updated. Check out the latest.
Forum: 3D PRINTED RELATED ITEMS
While the 40 brass will fit in the small collator plate, I don't think many will drop in. I did all my testing for .40 using the large plates.
Forum: 3D PRINTED RELATED ITEMS
I just added a new 5.45x39 feed die to github.
Forum: 3D PRINTED RELATED ITEMS
I am looking at the manual and will put a statement in there that the nut is required.
Wait NVM. it is already in there.
"This main bracket replaces the stock APP tube brackets allowing for...
Forum: 3D PRINTED RELATED ITEMS
It was designed to have one of the 1/4" nuts where you indicated.
Forum: 3D PRINTED RELATED ITEMS
Tander's is a good friend of mine, and I feel his pain. Once you share your design freely you are at risk of being taken advantage of. I have been fortunate with the collator because there are a...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |