I tried to private message you, but it says you are full. I am interested if it’s still for sale.
Type: Posts; User: DirtyDusty
Forum: Muzzleloading.
I tried to private message you, but it says you are full. I am interested if it’s still for sale.
Forum: Muzzleloading.
What kind of powder charge were you using? Btw, I saw a closed thread where you were selling an encore ML bbl. You still have it?
Forum: Casting Equipment
Same here, I ordered a mold a month ago and had it a week later. Had a question about another mold I wanted and sent emails to both addresses and a message through messenger. No response from any of...
I despise smith and Wesson’s service dept. hopefully I never need them on this pistol. I have an TC encore .50 caliber muzzle loader. After probably 50 shots the barrel started swelling up about a...
I messed around with it earlier. With the 125gr rfn I bought off of the swap and sell section, I have to seat to an OAL of 1.025. I reduced the load to 3.7 gr. Of 231 and going to start there. This...
Forum: Coatings and Alternatives
Is letting the bullets stay too long in the oven detrimental? I mean if you get them to temp and they stay another 2 minutes, other than the color getting darker, will it cause coating failure?
Anyone shooting cast in theirs? I tried a 125 tc and a 125 round nose. .356 and both fail to let the slide go forward all the way. Locks up and when I finally get the slide to pull back, the bullet...
Forum: Reloading Equipment
I started reloading 9mm cast on my older Dillon 1050. I am using Dillon does and they size the die down pretty tight. The powder funnel bells the mouth out slightly, but once you load the bullet in...
Forum: Lead and Lead Alloys
I know of about roto metals, but who is the cheapest source of tin online?
I am going to order a pack first, thanks for the offer. I just received my mold earlier this week. It only cane with 6 clips and no set screw. Do you, by chance, have the size for the set screw that...
Does anyone happen to know what size the clips go on the hollow point pins? Need to get some spares
That’s sounds like a pretty warm load too. Do you know how big the meplat is on that bullet?
Forum: Lead and Lead Alloys
I used a 5 quart Dutch oven from Wally World. Kept my probe on the bottom and kept the heat low till the lead got soft and kept pushing everything down to the bottom until I got a good pool of lead...
Forum: Lead and Lead Alloys
“The rest” were all the clip on weights. I didn’t want to hand check each one so I used temp to segregate the zinc and ferrous ones.
Forum: Lead and Lead Alloys
I had 2 5 gal buckets that where 3/4 full of wheel weights. Been setting in the shop for 4 or 5 years. Decided if I am going to get into casting, I needed to make ingots. I sorted the stick on from...
That matches the velocity of my loads, very closely, as I was working up to 24gr. in .5 gr. increments. Thanks
Bullet is a wfn from a mountain mold. The gentleman sold the mold, but I sent a bullet in to mountain molds and he said that it is a 300gr. bullet with wheel weights, but these where cast with 50/50...
Forum: Hunting with CB's
I am using a semi-auto. Built it for hunting, but not really impressed. Shot several deer with it using 125 sst and 125 ballistic tips. Lost one with a behind the shoulder shot, very little blood....
Forum: Hunting with CB's
Anyone using cast boolits for white tails in the 300blk?
You are correct. Lol. It’s a .44 magnum in a Ruger Bisley Blackhawk Hunter.
Anyone know what the max load is in a .44 magnum with a 285 cast wfngc using h110? Was working a load up today, in my Ruger Bisley Blackhawk Hunter, trying to duplicate an old load I had, but lost...
Forum: Coatings and Alternatives
So where can hi-tek be purchased in the states?
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |