I'll take # 10. PM inbound
Type: Posts; User: Astocks2622
Forum: Lead and Lead Alloys
I am fairly new to casting, and have focused primarily on bulk pistol bullets so far.
I just got an NOE 300gr gas check HP mold to use in my 35 Whelen. My primary purpose for it is to develop a...
Forum: Cast Boolits
This is the bullet I'm using.
https://www.accuratemolds.com/bullet_detail.php?bullet=40-200A
Sent from my SM-G970U1 using Tapatalk
Forum: Cast Boolits
I run a Tanfoglio 10 as well. I've not tried SWC bullets, but could see them getting a little hammered. I use a 200 gr WFN, but I'm using a harder alloy, water dropped. I get a little deformation...
Forum: Completed Deals
Pm sent.
Sent from my SM-G970U1 using Tapatalk
Forum: Completed Deals
I'll take the trimmer. Sending pm
Sent from my SM-G970U1 using Tapatalk
Forum: Cast Boolits
Well, shoulda slugged my barrels a while ago.
458 slugged at .459-.4595. so it looks like I need .4605
And my problem 9mm slugged at .3565-.357. actual bullets after sizing were .357, so maybe I...
Forum: Cast Boolits
I've been shooting 147gr out of my 9's for 10 years with no problems. This mold is actually slightly shorter than the plated bullets I've been using. I don't think that's the issue with the 9. ...
Forum: Cast Boolits
Thanks. I've not had accuracy issues with any other bullet in the 458 socom, so wouldn't think I have an alignment issue with the brake? Barrel is a Tromix 1:14 16.25". 1600fps is about the top...
Forum: Cast Boolits
The 35-147c is being used in a 9mm, so .355, nominally.
The socom is 458, supposedly. I'll cast some pure PB of each to slug the barrels.
Sent from my SM-G970U1 using Tapatalk
Forum: Cast Boolits
I wrote a while ago about the great success I had with my first casting session making some 200gr 10mm hardcast. They have proven accurate and reliable; I'm completely satisfied with them. ...
Forum: Completed Deals
Is it $85 each, or are you selling them as a package deal? I'm interested in the 35 cal, but don't have a 44.
Sent from my SM-G970U1 using Tapatalk
Forum: Completed Deals
I'll take one. Pm inbound
Sent from my SM-G970U1 using Tapatalk
Forum: Completed Deals
These are a good bit bigger than the rcbs ones, correct?
Sent from my SM-G970U1 using Tapatalk
Forum: Casting Equipment
I drilled a small hole in my Lyman 45 base for the tip of a soldering iron to fit into. used a cheap amazon soldering iron with dial-controlled heat output.
Forum: Cast Boolits
The feeling is mutual, though opposite. 100 sounds like hell to me. There's only so much clothing one can appropriately remove. I can always add a layer. We're in Alaska, and winter is gorgeous...
Forum: Cast Boolits
a normal high for us is about 70 in the summer. once in a blue moon it will hit 85. i'm more concerned with low-temp performance, when it's 10 below here. I am using an old lyman 45 lube-sizer,...
Forum: Cast Boolits
I have White Label Lubes BAC and Carranuba Red. I used the BAC this time. My goal was 20-21 bhn with quenching, and I landed right about there. Sized .4015. Only fired a dozen through a...
Forum: Completed Deals
If only we were closer. It's been 2 years since I've seen small pistol here in Alaska. I have a decent stash of large pistol, but I'm down to less than 500 small pistol. Good luck
Sent from my...
Forum: Cast Boolits
Thanks! I was having trouble if I let it cool much more, then the sprue plate had to be gently hammered open with a rubber mallet instead of just pressing it open with a gloved hand. Am I missing...
Forum: Cast Boolits
Close, it's actually an Accurate Molds 40-200A. Cast with 2:1 pb:lino and quenched.
Sent from my SM-G970U1 using Tapatalk
Forum: Completed Deals
I'll take 4) IDEAL 457124. Pm inbound
Sent from my SM-G970U1 using Tapatalk
Forum: Cast Boolits
Thanks to the stickies here, my first casting session was a complete success yesterday! From learning about lead alloy metallurgy and matching alloys to intended uses, to learning how to judge when...
Forum: Cast Boolits
Incredibly simple. Still helping us newbies 8 years later. thanks to Gear for taking the time to write this up.
Forum: Hunting with CB's
Absolutely. I've taken many grouse while hunting moose and black bear here in Alaska, both with firearms and archery. My primary rifle is a Mauser rebarreled to 35 Whelen. 250gr Partition at 2650...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |