How the heck did you lube them size boolits in that sizer ? hehe
Keith
Type: Posts; User: IcerUSA
Forum: Cast Boolits
How the heck did you lube them size boolits in that sizer ? hehe
Keith
Forum: Our Town
Check out MidwayUSA's clearance , http://www.midwayusa.com/static.exe/getstaticpage?page=622201016_page.htm&eblastid=622201016&custnum=100950591&utm_source=viewonlinetop&utm_medium=eblast622201016
...
Forum: Our Town
Got the flag today . nice flag that will look good in my new reloading room when I get it done . LOL
Again thank you Ken for all your work here at CB .
Keith
Forum: Our Town
Hey , if there are some still available put me down for 5 and an address to send funds to .
Keith
Forum: Leverguns
If the 444 is what you want , I'd go for it , you can always sell it if it don't work out , but you ain't going to get mine . hehe I would also look for a boolit in the 280gn area and push it about...
Forum: Cast Boolits
First off , Welcome to CB's .
When I do my HP Moulds I use a ladle to pour with and let the extra lead pour over the side of the mould back into the pot , seems to keep the mould warm and gives...
This is off his web page.
bullshop@wildak.net<bullshop@wildak.net>;
Keith
Probably just the alloy is your weight differance , I wouldn't worry bout it though .
As long as the as cast size is good for your pistol I would lube and shoot them .
Keith
Forum: Our Town
Good thing we usually don't have to weld on our molds often . :)
But welding of any kind has safty things that should be done everytime you weld .
Keith
Forum: Our Town
Looks like he's out of everything , but he has an order in for more so he will have something soon , I'm sure .
Keith
Forum: Our Town
Have you cast any from your mould yet ? If so , what do they mic at ? I would use any of the tumble lube boolits that mic .357 to .360 and see how they do . Might need a sizer to crimp on gas checks...
Forum: Single Shot Guns
For an athentic looking scope for the late 1800's the Wm. Malcolm is the cheapest out there . Does your barrel have a dovetail for a front site ? If not you may be limited to the short scope .
Check...
Forum: Lead and Lead Alloys
WARD O
I would check to make sure the pin is center of the cavity . Mine is not so it will forever be off center as the pin is put in the blocks after the cavity has been cut and the mould has set...
Forum: Our Town
Check here : http://www.handloads.org/loaddata/default.asp?Caliber=45%20ACP&Weight=200&type=Handgun&Order=Powder&Source= might find something usefull , or go to the powder web sites .
Might be a...
Forum: Our Town
Yep , that be Dan I got some from , BABore . One thing about Dan is he will tell scalpers who want 10k to go away and not come back . :)
Keith
Forum: Our Town
My supplier still hasn't gotten a full order of primers yet so he rations his . He did say that ammo is starting to come in for pistols tho . Primers cost $30.99 + tax so not too bad .
Keith
Forum: The Star Equipment Corner
Did you check this out ? http://www.magmaengineering.com/PDF/StarInstructions_012009.pdf
I found it takes awhile to get it just right , Might want to take the sizer out and clean it and set the...
Forum: Cast Boolits
I've run some boolits with only 50% lube in the grooves , I use WFFL , and have had no problems with lead build up . As long as they are mixed with the full luge grooved ones I don't think you will...
I had problems with Power Pistol once it got below freezing , so I saked my powder guy what he would suggest and he told me to use Titegroup in the colder weather . Might not be the hottest but it...
Forum: Cast Boolits
Are you FL sizing the brass ? What diameter is the boolit ? What is the inside of the case after sizing ?
Just a couple things to think about . :)
Keith
Like Ben , I start load development , but at 25yds , then when I think I have a good load I then got to 50yds to confirm the load , you would be surprised even at that difference how much things...
Forum: Casting Equipment
MMA10mm , The flow lever is the silver thing you see on the top in the pic , just lift the lever and a rod that is attached to the lever rises .
Mine has a screw that limits the amount that the...
Forum: Casting Equipment
Well , I got the pot from Springfield and got a element and thermostat for it , I think this thing holds 40 to 50 lbs of lead 1 inch from the top . Only problem for casting with it is the amount of...
Forum: Casting Equipment
Thanks for the link , looks like it would work on the old pot I have , just need to fimd an element that will work in it now . It's an old Hilts pot with about an ID of 4 1/2 to 5" dia at the base...
Forum: Cast Boolits
Does your .410 have a smooth bore ? Might have to look for a rifled slug mould if it does or it's not going to shoot very far accurately . I used to shoot an old bolt action Mossberg that my step dad...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |