Load DataLee PrecisionWidenersMidSouth Shooters Supply
Inline FabricationReloading EverythingTitan ReloadingRotoMetals2
Repackbox

Search:

Type: Posts; User: Rrusse111

Results 1 to 18 of 18

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    2,191

    Thnx for the heads up, I got half a pound of...

    Thnx for the heads up, I got half a pound of metallic red Eastwood Hot Coat, I think, cheap. Found a tray, after some mods with the grinder, that'll fit my oven, which does heat up. I'll start slow.
  2. Replies
    16
    Views
    2,191

    I'm looking to join the club here. Got an op...

    I'm looking to join the club here. Got an op shop oven for $24 and half a pound of powder coat paint. Could use a tray, I'll dig around a bit and see if I can come up with an appropriate size. ...
  3. Forum: Leverguns

    Accuracy Problems with the 44Mag in the Marlin...

    Accuracy Problems with the 44Mag in the Marlin 1894 are common. They've got a long throat to accomadate a longer COAL, this was a factory configuration. 44Spec in the initial 336 version would have...
  4. Thread: 375 Win

    by Rrusse111
    Replies
    35
    Views
    3,820

    Forum: Leverguns

    Paul, PM'ed about the brass. Cheers! Richard

    Paul,
    PM'ed about the brass.
    Cheers!
    Richard
  5. Replies
    73
    Views
    12,216

    Forum: Leverguns

    My walk around load; 9.5 gr of Blue Dot with the...

    My walk around load; 9.5 gr of Blue Dot with the Lee RF 158gr boolit; Marlin 24"CB. Circa 1450fps and deadly accurate.
  6. Replies
    25
    Views
    2,765

    Forum: Leverguns

    Gents, I know Redman and John Taylor do great...

    Gents, I know Redman and John Taylor do great relining, unfortunately both are swamped with work. Redman's liners are only recommended for pistol calibers, whereas TJ liners are hammer forged...
  7. Replies
    17
    Views
    5,734

    Forum: Leverguns

    Marlinman93, You're the man that may be able to...

    Marlinman93,
    You're the man that may be able to confirm this, the 25-36M is reported to be a 1:9 twist vs the 1:10 of the 25-35Win. I have a very worn TD barrel in 25-36M that needs relining, I...
  8. Replies
    141
    Views
    16,414

    Forum: Leverguns

    "No picture of groups, cause they weren't...

    "No picture of groups, cause they weren't groups!! Haha
    Nearly all of the lead is near the muzzle and it seems like there's a lot."

    Kroil will help in removing the lead.
  9. Replies
    141
    Views
    16,414

    Forum: Leverguns

    Lol, hornet's nest ehh. You fellers do what ever...

    Lol, hornet's nest ehh. You fellers do what ever you want. Have fun, or next I'll bring up politics,,,,,,,,
  10. Replies
    141
    Views
    16,414

    Forum: Leverguns

    Short answer, yes, I have shot it. My original...

    Short answer, yes, I have shot it. My original comment still stands. Messy, dirty, explosive, and corrosive, give me smokeless every time.
  11. Replies
    141
    Views
    16,414

    Forum: Leverguns

    I have one of these in a Miroku build TD, I would...

    I have one of these in a Miroku build TD, I would NEVER consider running BP through it. Just use 45/70 data to reload, with the longer/bigger case you won't have any problems. Starline brass and...
  12. Forum: Leverguns

    Blue dot, I got a lot of it.

    Blue dot, I got a lot of it.
  13. Replies
    19
    Views
    1,981

    Forum: Leverguns

    .379 and the long starline brass, Lee dies.

    .379 and the long starline brass, Lee dies.
  14. Replies
    100
    Views
    8,035

    Forum: Leverguns

    A 336A (24" barrel) Octagon would be ideal, but...

    A 336A (24" barrel) Octagon would be ideal, but I'd settle for round. in 25-36 Marlin. And while they're at it, one in 219 Zipper. Lol, I just got a set of dies at a gunshow.

    I'll second the...
  15. Replies
    32
    Views
    102,301

    Sticky: I've hand cut a couple on my 44-40 barrel swap...

    I've hand cut a couple on my 44-40 barrel swap into a Marlin 1894. I didn't want the full length magazine tube. For a filler blank, a bevel gauge and a protractor gives a good reference on any bit...
  16. Replies
    15
    Views
    2,063

    Forum: Leverguns

    "1895 22" barrel version has a higher spring...

    "1895 22" barrel version has a higher spring tension than my 26" barrel Cowboy version"

    Probably the same spring.
  17. Replies
    23
    Views
    3,728

    Forum: Leverguns

    Mk42, The long brass with the .006" thick neck...

    Mk42,
    The long brass with the .006" thick neck IS the right dimensions for the chamber. And while some have re-reamed, generally at the cost of sacrificing accuracy, it's simply unnecessary. Leave...
  18. Replies
    100
    Views
    8,035

    Forum: Leverguns

    1894 in 327 Federal Mag. 22" long 1/2 octagon...

    1894 in 327 Federal Mag. 22" long 1/2 octagon barrel with a 2/3 magazine tube, pistol grip.
    No checkering so I don't feel bad about trimming the stock and forend down.
Results 1 to 18 of 18
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check