Search:

Someone here recommended this mirror a while back. Clipped on to the brass feeder I can see in both collators, nice for seeing if a plate is jammed when I have music going or running the trimmer on...

Thanks for the tips on the stuck bullets. I’ll try printing the new peer drop tubs mine are probably 2 years old. In looking at the issue, seems like three bullets are lodging in the tube just above...

The bunching up is due to a bullet resting above the drop tube in the spring at a sharp angle then another bullet coming and wedging against it. I have minimized it by getting the spring to be closer...

GWS - Can you please share what spring you are using? In the video it looks like a smaller dimension than the DAA MRBF ones. I am having issues with 55gr 223 occasionally bunching up at the top of...

I don’t have any input on a better spring but the one you have is what I use for coated Bayou 9MM.

Hi - Any suggestions on what to clean carbon off the feeder bowl and the plates? I am using Overture PLA Pro. Was thinking of using some diluted isopropyl alcohol which seems safe from what I have...

Sorry for short notice Amazon has overture PLA pro for $16-18/roll for next few min. I got some Dillon blue for $31 for two pack.

Was definitely a faulty sensor, changed it out with a spare and everything worked properly.

Is it possible to wire the prox sensor such that it powers on when metal is near it or did I get a wrong part? The labeling is the same as the other prox sensors I have. Not a newbie here, but very...

@corbindallas and @JStuhmiller - apologies - I got my wires crossed. I should have waited until I was in front of the PC rather than trying to use my memory.

The box I used is from Tanders Dillon...

IIRC this is an alternate box someone else created. I believe it is in the contributors folder. If you can’t find it I can do some searching and come up with more info. I definitely got it either...

I had to file and sand it to get it to fit.

In the contributors section of the files see <edited> KC10 Kevin Dillon Mount

There are files to connect a square tube to the post on the Dillon. Works awesome! Please ignore my bad cable...

Cold air/drafts can affect printing. I had occasional issues with bigger prints lifting due to drafts in the basement. I bought the Ender enclosure and have not had an issue since. Many people use an...

Thanks Tyler, I started printing it oriented like in the manual before seeing your post, go figure… Print came out okay without supports; needs a little sanding at the apex, but considering what it...

I gave up on PETG on my Ender 5 trying to make AR15 mag loaders; lots of stringing. The Overture PLA pro/plus has been really consistent for me and easy to print. If PETG works for you go for it, but...

Thanks tt365. I have the collator and never understood why I would need a bigger one until I started mass 223 case prep on the APP. As I started to add more handfuls of 223 it started spitting an...

Hi - I am planning to print the main body wall extender in the orientation shown in the manual. Even if I set supports to 70 degrees there is a bit showing as needing supports. Looking for...

I used to use a Lee Pro 1000 with their bullet feeder and the collator/drop tubes. 124 round nose coated bullets (Bayou Bullets) fed well. I had issues with Berry’s copper plated 124 round nose...

It took me four months to get around to this but I printed out the parts and can confirm it works fine with the Geartisan $15 motor on the Ammo Mike bin. Was planning to use this for depriming 223 on...

I have some electrical tape going from the case feeder hole plug to the middle of the bullet feeder spring so the spring has about 3-4” of spring straight up and down for the bullet to go directly...

I had awful results with TecBears PETG lifting and stringing and switched to Overture PETG and it worked much better, still never got it dialed in and just went with Overture PLA+. Was making AR...

Automation for case prep for a Rock Chucker?

Edit...I should have scrolled down :veryconfu

Thank you GWS!

Very interesting GWS - can you please share the parts you created to fit the AM for brass collating?