Search:

This reminds me of the time I was up in the cheap seats at RFK stadium watching Edie Brickell open for the Dead and way down in the grass all the way across the field on the sidelines these people...

In addition I hear Al Storey makes a good one. Borschardt Rifle Co in NM.

Here's one.
https://www.goonsgunworks.com/

Most jacks have a bypass valve that will eventually activate to prevent destroying the jack. I can cycle mine until I feel it start to bypass, and that's all I get. That does happen about the same...

Next time try a full load of 35 grains and soft lead if those were hard.

I have several tons of wheelweight metal stashed at my house in Albuquerque. I'd be glad to trade you one for one for the entire batch. I always am looking for soft lead.

It will be just fine in the revolver. Lack of lube is much more of an issue in rifles.

Indian Joe, I tried to say the same thing but you said it better. This stuff is easy, just has a couple of rules to follow.

I agree, you would probably end up with a much softer lube. Maybe need a bit more beeswax.
As a source for mutton tallow, I found out my local meat cutter does a lot of lambs in the spring and was...

The trick is .4641 times the diameter of the bore (or ID of the shotcup) to get the ideal size for stacking in threes.

Good BP lube helps keep the fouling soft so it gets blown out of the muzzle and not accumulate in the bore as a hard crust. When you get the hard buildup, it resizes the bullets and both kills...

That '58 Remington he is shooting is more difficult to clean than your Uberti SAA. OK, not difficult but more involved. It looks like you have already bought a conversion cylinder, but at any rate...

I am sure lobbying had a lot more to do with this decision than performance or practicality. When you are the only one making the guns and the ammo, you have an interest in it being adopted.

I'm...

Since Hodgdon sold Goex, all they have now is that new type of fad smokeless powder which we all know will fall out of fashion before long. So no monopoly.

How exciting. They have managed to do what Burris has been doing for the last 10 years or so with their Eliminator scope.

That new round is going to be incredibly expensive to manufacture...

At our club anyway, since pistol caliber levergun uses the same course of fire but is way easier to make hits, everybody went to that because making hits is fun. I did both for a long time but...

Neat! Nice find. The false muzzle looks like it is set up to use a cross patch. Two thin strips of paper that fit in the cut out slots. The bullet will depend on the twist rate of the rifling and...

Are they using the SPC or the new SIG Fury? The SPC isn't even close to a 7.62x51.

You are right, you don't want to press the fines together or you are making a rocket engine. Just like if you light a pressed puck, it doesn't burn very fast. But take granulated pressed powder and...

After learning about those Bartholow cartridges I have been meaning to try that. I need to make a mold/form for them first, then some nitrocellulose glue to hold them together. I'm pretty sure it...

I didn't know anybody was still shooting IHMSA. I was really into it through the 80's and 90's but everybody in Albuquerque seemed to give it up. I shot NRA silhouette for a while after that and the...

I bought a 336 chambered for 35 Remington that had a gouge in the chamber and wouldn't extract a fired case. I rechambered it to 358 Win, and opened up the bolt face slightly to fit. It runs 308...

I always crowned octagons just like normal barrels after threading. 11 deg. cut then a ever slight chamfer to break the edge of the rifling to prevent cleaning rod damage. And yes, 4 jaw chuck and...

$65

Yes they are and you must be extremely careful while handling them.