Search:

Ive used redding products for a long time never with a complaint or problem. Ive talked with them several times on different things though and they were also very helpful.

I believe you could use a 45-70 case in your 410 or 40-65 they are both 2.1 long so still under your 2 1//2 chamber. You could use the same or close to it powder charge but have a heavier load of...

Where some works well is as a release agent or resist for bedding and things of that sort.

For patching the nail holes in the old roofing, Look at body solder and the tech for patching car bodies in the 60s. They would fill some pretty big holes with screen and 50-50 solder. For strength...

There is also the age old method of lapping the mould out. this increases the size and improves the roundness of the bullets. This process actually removes metal so go slow and measure often, once...

I like the Tony Packos chilli dog sauce. Along with their pickle and peppers relish. Home town restaurant thats branched out some.

Where the standards calibration and iso things are Important to industry is parts made in one shop or factory have to fit with parts and pieces made in 3 or 4 others. The closer the tolerances are...

The blue jays came back here a few days ago

Also remember annealing of the steel isnt the only thing that can happen when the fire dept comes in spraying cold water the steel can also be hardened becoming brittle.These changes cant be seen...

I would bet most reloaders never use any of the measuring jaws but the outside jaws. very seldom in side and almost never the depth laws either step.
When ISO calibrated all 4 jaws have to read the...

The other issue with used galvanized roofing is the oxidation may make soldering harder.

In also size before chamfer and deburring to make sure the mouth of the case is as round as possible. I use the wilson style tools. On handgun brass its trimmed when new or new to me. rifle brass is...

Welcome and enjoy the company

I would definitely look at the 148 grn wad cutters. Back in the day a lot of law enforcement issued snubbies carried them with good results.Another consideration might be to go down to one of the...

I could do that in my radial arm, set a long screw in the action clamp in vise and then set stock on maybe one strap clamp on top to keep it from pulling off/shifting. may have to look at that. The...

I lay out front and back then put an angle plate on the lathe compound align with center in chuck and tail stock. then drill straight thru. Little more set up but its accurate, And I have the lathes...

Im thinking know the counter top is an excuse to make sawdust because your getting low :kidding:

Not a problem CF I enjoy hearing others projects. You will get a lot of fine sawdust there to flux with

I had pulled most of the chestnut molding out of the original family farm house before Dad sold it. Made him a cane from it and the 2 aunts a set of candle holders. To remember the farm.

Cured...

Also check the spring washer if it has one they have been known to break and bind

Found a disposable 9 X 13" aluminum baking pan 2 1/2" deep slid right under the bottom wheel and appears to be catching 90% of the chips. When some what full can slide it out and throw it all away.

Its a Roll in vertical cut off saw for metals. When I bought it I had the vise up graded and the air feed system added. Ive since added a scale to the back of the table and an oil mist system to it.

When building a pot mass is your friend it holds heat and gives more to work with.
The solder pots on the can lines were 60 or 70 pounds and had cartridge heaters in the bottoms If I remember they...

Back when I was scraping and hand fitting i could feel .002 between 2 parts. Seeing was a different story .010 with out a comparison part. would have been a good day. On a scraped pattern I could see...

Ive always wondered if a fine screen around the needle valve up to top of pot would help If your valve base is 1" then and screen rolled to 1 1/4" with a ring top and bottom to support it. This would...