2wheel you are correct but it's $19.98 plus Shipping
Type: Posts; User: tom357mag
Forum: Our Town
2wheel you are correct but it's $19.98 plus Shipping
Forum: Our Town
Yes it's for the auto disk powder measure. It's an injection molded disk that is discontinued because the die that Lee had broke and they never replaced it. It is great for small loads
Forum: Our Town
I have been looking for a Lee Micro Disk for a long time , just found one on ebay for $9.00 shipped!
Yay for me
Forum: Reloading Equipment
I also use the shellholder as my "collet" . Also might want to put a foam earplug in the bottom of it to save the bullet from the impact. JMO
Forum: Reloading Equipment
Take em apart and put them in a vibratory tumbler and tumble as you would brass. Add a capful of nufinish and they will come out clean and protected.
Forum: Casting Equipment
So I was casting yesterday with 2 seperate molds and both had the same problem. The screw that holds the sprue plate tight kept coming loose. It was a real PITA to keep tightning that screw during...
Forum: Reloading Equipment
Put them in a tumbler with a capful of Nufinish and they will come up clean with a light coat of wax to protect them.
Forum: Reloading Equipment
YES YES YES!!!!!!!! Tumble them with Nufinish , you will not regret it. I have done it and it works great. Take them apart and tumble as you would brass.
Forum: Casting Equipment
You need to "smoke" the mold with a wooden match or candle and the boolits should just drop right out. Give it a try before you call Lee.
Forum: Casting Equipment
Can't complain about that! I have been using Lee equipment for over 25 years with no complaints. Great to hear good things about Lee.
Forum: Reloading Equipment
The piece with the primer cup is replacable so do not file anything. If the small primer works fine what you need to do is to try and push the piece with the cup on it deeper into the actual piece...
Forum: Casting Equipment
I use a SS tablespoon , SHHHHHHHHHH! the wife don't know lol
Forum: Reloading Equipment
Never had a problem with the Lizard Litter clogging the flash holes. Also put a capful of NU-FINISH car polish in it , let it tumble for 15 minutes , put the brass in and check in 2 hours. It will...
Forum: Reloading Equipment
I've loaded over a 1000 and they ALL went bang
Forum: Reloading Equipment
Well said 462 , I personally tumble with primers out. Lizard litter and NU-FINISH car polish. Works for me :smile:
Forum: Cast Boolits
I am certainly not new to reloading but new to this cartridge. My brother just had to have one! I am thinking about getting the Lee C501-440-rf-gc mold but here's the down side , I want to reload...
Forum: Reloading Equipment
You can also trade brass for what you personally need. Its a great way to get things you need right now with the way things are. Just a suggestion.
Forum: Reloading Equipment
Great Job !!!!!!!!!!!!!! Well done and keep up the good work on this site. Nice to see someone taking the time to preserve some history. Guest #515
Forum: Reloading Equipment
vibrating tumble with NU-FINISH / walnut media and they will come out looking brand new!
Forum: Reloading Equipment
Be careful you make sure to get the turret back on right before you pull the handle or you will strip out the little plastic ratchet piece. Order some from Lee because you will need some spares.
Nothing but good luck for me with LEE products in 25+ years. AAAAAAAAAAA+++++++++++
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |