Yes I was using gas checks. I have tried with and without and have more success with them on.
Type: Posts; User: Luigi Lavazza
Forum: Coatings and Alternatives
Yes I was using gas checks. I have tried with and without and have more success with them on.
Forum: Coatings and Alternatives
I was able to make it out yesterday with the newly scoped FAL and the remainder of the 100 that I coated and loaded up with the same recipe. Not good. I zeroed in the scope first with about 7-8...
Forum: Coatings and Alternatives
I swage once and only after coating. Swaging the linotype was definitely more difficult then the pure lead. I was having to spray them with my case lube first.
Forum: Coatings and Alternatives
HollowPoint,
i apologize. You also asked about the mold. They came from my new RCBS 7.62mm 130gr mold.
Forum: Coatings and Alternatives
HollowPoint:
these were launched from my open sight Argentine FAL with a 21" chrome lined 1:11 twist 308 barrel. This load was 45.5 grains of RL15 and the bullets were sized down to 308.
...
Forum: Coatings and Alternatives
yea it was just me yesterday and hadn't shot this rifle in almost a year. I didn't recall flinching so not sure what the flier was. I'll definitely load up 50 or so more and see if I get the same...
Forum: Coatings and Alternatives
Not sure if this qualifies but I'm super happy with it. Done at 50 yds since I was working up a load. Scrap Pb water quenched and weighed in at 139.5 each. Total group size was 1.5" with the 4 at...
Forum: Coatings and Alternatives
Played around again with my new RCBS 7.62 mould but this time sized them to 308
http://i57.tinypic.com/2mqndrq.jpg
fired thru a FAL only at 50yds using a FMJ recipe...
Forum: Group Buy Archives
Thanks Fishman.
this is exactly what I've been looking for:
http://noebulletmolds.com/NV/product_info.php?cPath=30&products_id=763
http://i59.tinypic.com/2rw9v8p.jpg
i wonder if removing...
Forum: Group Buy Archives
I would be interested but not at $240. Are you considering gas checks? A few months back I reached out to Kaine molds but never heard back. I believe they modify lee molds to remove the groves and...
Forum: Military Rifles
Fireball from my M48 with a cast load:
http://i60.tinypic.com/2qltq3q.jpg
Forum: Military Rifles
The problem is going to be headspacing as they headspace off of the locking shoulder similar to the FAL. But unlike the FAL I've never seen an assortment of them around.
Forum: Coatings and Alternatives
What they looked like as they dropped from the mould:
http://i60.tinypic.com/2rfy41v.jpg
After powder coating (tumble method) and sized down to .311
http://i60.tinypic.com/ws3dps.jpg
The...
Forum: Coatings and Alternatives
But now the good news...
i powdercoated some 308 lino 160's sized back down to 308 on top of 41gr of RL15. Fired thru a FAL at 50yds.
http://i62.tinypic.com/24odrf8.jpg
no leading in the bore or...
Forum: Coatings and Alternatives
http://i58.tinypic.com/zxtw13.jpg
http://i59.tinypic.com/2csdnrr.jpg
first 10 shots with soft roofing lead powdercoated 8mm. Shot from a Yugo M48 that will shoot Lino cast at 50 within 1". I'll...
Forum: Coatings and Alternatives
http://i57.tinypic.com/jzxzeu.jpg
oh yea...smashed one too for good measure
Forum: Coatings and Alternatives
http://i58.tinypic.com/aui5xy.jpg
Cast and coated some 8mm today with soft roofing lead. Hopefully will get a chance to try them tomorrow with my lubed Lino load at around 2400fps. Will post...
Forum: Swaging
Granulated Lead? Would this be similar to chilled #9 or smaller shot?
Forum: Swaging
Thanks to all. Have not purchased a swaging die set yet. Just gathering a grocery list and looks like cannot cut the core mould.
Forum: Swaging
Is there a method of pouring cores directly into the jackets? I would think if possible you would first need to pre-heat the jacket to get a good fill (assuming it would be like a mould). This...
Forum: Hunting with CB's
PLS1911,
Thanks for the tip. I will definitely give that a try.
A little off topic but tried straight lino in my 1911 and got some good leading. I read more here and discovered that lino...
Forum: Hunting with CB's
Mike,
No sir. I didn't know if/how the 100% lino .323's would expand so I took a head shot. It went clean thru and didn't appear to fragment at all.
I smoked 1/2 that evening and took the...
Forum: Hunting with CB's
Took a 100lb hog over this past weekend with my lino 8mm Saeco cast thru a Yugo M48. I push mine pretty hard (same loads as FMJ) and the impact at 100yds snapped its neck.
Thanks to all who post...
Forum: Military Rifles
Very Nice. I have been able to achieve regular 1.5-2" groups with RL15 and 168SMKs with my DSA non-Steyr barrel. They are fun to shoot but super heavy to stalk hunt with. I had a Nikon Buckmaster...
Forum: Our Town
Howdy from Texas! I've been reloading for about 2 years. Saeco #311 will hopefully ship next week so I can start playing with lead.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |