Search:

Yes we had to dissolve the partnership. It has been very frustrating indeed. Mike and I are still on good terms, and I am glad to have put the partnership problems behind us.

There are...

Alan,

Both of the machines were shipped out in the condition which they were sent. The one did acquire a small scratch (no dings) between having it at our facility in Grand Forks and moving it...

There's a disc spring on top which lets you adjust tension on the sprue plate. They're special order, but we can send you more if yours wore out. Also make sure the set screw on the side is real...

Mozeppa- I have been trying to contact you. Please give me a call. If I don't answer the shop line, I left my personal cell number in an email as well as a message on your answering machine. Lets...

Hi,

A razor blade used carefully works well. Just keep it away from the cavities because you can nick them with it. There are also two other ways that we prefer. The first is using the edge of...

BWatson,

I sent you a PM with no response a couple of weeks ago. Send me an email and we can get any issues you are having cleared up in as timely manner as possible.

Thank you,

Derek...

We manufacture the Keith designs as well if you are interested.

They are designed to be interchangeable with the Star die so they work on any Magma or Ballisti-Cast machine along with ours. The outside of them is turned just under the diameter of the standard...

Hi Guys,

We have already developed the shorty size dies for coated bullets. They are turned out of hardened 4140 steel, and are in stock. We have them currently available in 9mm, 40cal, and 45cal...

Hi Wreck-n-Crew,

Our four cavity molds meet all of the criteria you have listed. They are cast iron, manufactured to your alloy and specified diameter, have a thick steel sprue plate and we have...

Yes we have had a setback from the lead times we had been giving. We are back up and running to full capacity now, but are still at extended lead times due to the downtime.

I would like to...

PM sent to BWatson.

Yes it is our machine. Message me and we'll get one, two, or even a few on their way to you. :-D

Hardened male and female inserts would be installed in the original holes if possible otherwise new holes would be drilled and reamed next to the original ones.

We were sent in a H&G mold with the standard 2 round pins on one side only. The mating side of the block with the two chamfered holes was severely worn as is common in the old well used H&G molds. ...

Hey guys check this out:


https://www.youtube.com/watch?v=7pi4cEHMj1s

Its our 38-115-BRN1S bullet design coated with Zombie Green Hi-Tek from Gateway Bullets. What a beautiful coating. The...

Bigarm we picked lead balls up at the local Scheels, but you can get them from Midway: http://www.midwayusa.com/product/1165132904/hornady-muzzleloading-bullets-round-ball. You don't have to be more...

Very nice looking bullets bigarm!

Thank you everyone for the constructive criticism. All of your comments are taken into consideration. We recently revamped our website trying to ease browsing,...

We tried slugging a .308 rifle barrel with a .312 bullet cast with 92:6:2. The bullet stopped moving when it was half way into the barrel and it was tough to get out. A 100% pure lead round ball...

Yes. It's sitting on the shipping table ready to go out today.

WD-40 and green scotch brite pads is what we use. The other ideas along with 0000 steel wool should work too. If you use steel wool, stay away from the cavities with it because steel wool can round...

I would like to clarify that it was suggested to not use it on the mold itself or in the cavities. As shooterAZ stated it is not recommended to use in the cavities because it will alter bullet...

We ship the molds out with WD-40 to prevent any rust. The downside to this is that the WD-40 penetrates the cast iron and needs to be burned off before you get perfect looking bullets. We put them...

Hello Everyone,

Thank you all for the support and continuing patronage. We greatly appreciate the reviews and customer feedback on our products and services.

Bigarm: Your order is complete and...

Frankford Arsenal mold release makes a noticeable difference in keeping lead from soldering to the faces and top of the mold. Moly-Dri Lube Plus from Certified Labs works even better. It's more...