Inline FabricationReloading EverythingLee PrecisionPBcastco
MidSouth Shooters SupplyTitan ReloadingWidenersRepackbox
RotoMetals2 Load Data

Search:

Type: Posts; User: PJEagle

Page 1 of 8 1 2 3 4
Results 1 to 25 of 193

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    242

    WTS Closed

    Closed
  2. Replies
    4
    Views
    242

    WTS WTS - 9MM Brass – Ready to Reload

    WTS - 9MM Brass – Ready to Reload

    9MM Range Brass that has been inspected, decapped, sized and cleaned in a wet tumbler. It was finished with automotive wash & wax. 500 count plus an extra 10...
  3. Replies
    14
    Views
    571

    As long as the boolit is pure lead it should work...

    As long as the boolit is pure lead it should work fine. Make sure the bore is clean. Lube the barrel and the boolit. Then use a Plastic tipped hammer to drive the boolit into the barrel. Use a...
  4. Replies
    9
    Views
    1,273

    You should be able to size the .379 down to .377...

    You should be able to size the .379 down to .377 without any trouble. I use NOE's sizing kit and bushings.
  5. Replies
    27
    Views
    1,031

    I had some similar experiences with a couple of...

    I had some similar experiences with a couple of Springfield Armory 1911's. The first thing I did was to sort my range pickup brass by headstamp. The second thing was to sell my case gauge, remove...
  6. Replies
    16
    Views
    1,323

    This is a link to the NOE .453 plug. ...

    This is a link to the NOE .453 plug.

    https://noebulletmolds.com/site/shop/bullet-casting-reloading/expanders/expander-plug-pistol/453-x-449-p-exp-plug/
  7. Replies
    63
    Views
    3,431

    Forum: Cast Boolits

    Frankford Arsenal makes a wet media separator...

    Frankford Arsenal makes a wet media separator that removes the pins from the brass in about a minute.
  8. Replies
    23
    Views
    1,702

    The thermocouple came from Auber Instruments. I...

    The thermocouple came from Auber Instruments. I really like the stand. I wouldn't want to be without it.
  9. Replies
    23
    Views
    1,702

    I drilled a hole in the center of my pot lid and...

    I drilled a hole in the center of my pot lid and used a brass compression fitting to hold the thermocouple about a half inch above the bottom. This my original Lee pot with a My2ndRight stand....
  10. Replies
    19
    Views
    946

    NOE makes a 180 grain WFN. It feeds well in mine.

    NOE makes a 180 grain WFN. It feeds well in mine.
  11. Replies
    18
    Views
    756

    Forum: Our Town

    I am guessing that you are using white beadboard,...

    I am guessing that you are using white beadboard, sometimes referred to as Styrofoam. If that is true, don't use construction adhesive. Locktite PL 300 is the proper adhesive. It comes in large...
  12. Replies
    14
    Views
    858

    Most people recommend .001" over the bullet...

    Most people recommend .001" over the bullet diameter. I have found that .002" over the bullet diameter works best for my 9MM, .357 and 45 ACP rounds. Since they don't cost much, I would purchase...
  13. Replies
    29
    Views
    1,829

    It's a USPS Small Flat Rate Box for Priority Mail.

    It's a USPS Small Flat Rate Box for Priority Mail.
  14. You can order a custom seater plug from Lee for...

    You can order a custom seater plug from Lee for about $18 shipped. Look on their website.
  15. Bump To The Top.

    Bump To The Top.
  16. WTS – Redding & Lee Dies & Dillon 45 ACP Case Gauge

    1 – Redding .357/.38 Special Micro-Adjustable Profile Crimp Die – Used, but like new - $43.00

    1 – Lee Carbide 45 ACP Sizing Die – New - $13.00

    1 – Lee 45 ACP Seating Die – New - $8.00

    1 –...
  17. Replies
    4
    Views
    517

    Doug, Thanks for the update. I'll be glad to...

    Doug,

    Thanks for the update. I'll be glad to wait for your 9MM service.
  18. Replies
    10
    Views
    633

    I need a little more information before...

    I need a little more information before attempting to help. Is the Lee flairing die a powder thru flaring die?
  19. Replies
    17
    Views
    803

    Forum: Our Town

    I have used 3 RCBS ultrasonic cleaners in the...

    I have used 3 RCBS ultrasonic cleaners in the past three years. The electronics failed on each one within a year. Usually the heater fails first. I really like an ultrasonic cleaner for firearms...
  20. WTB It's not a single die. There is one for 38...

    It's not a single die. There is one for 38 Special and a different one for .357 Magnum.
  21. Forum: Cast Boolits

    I believe large rifle magnum primers are a little...

    I believe large rifle magnum primers are a little longer, front to back, than standard large rifle primers. You may have a problem trying to seat the magnum primers because the pocket will be too...
  22. Replies
    29
    Views
    1,333

    Forum: Cast Boolits

    Christmas is the season for giving, not getting. ...

    Christmas is the season for giving, not getting. Maybe we should thank our Savior for giving us eternal life.
  23. Replies
    2
    Views
    344

    Closed

    Closed
  24. Replies
    2
    Views
    344

    WTS - Redding Pro Series 45ACP Dies

    Redding Pro Series Sizing/Decapping Die
    Redding Pro Series Seating Die
    Redding Micrometer Seating Stem -Flat
    with box - In Like New Condition - $85.00 Shipped
    Will accept Cash, Personal Check or...
  25. Replies
    1
    Views
    356

    Closed

    Closed
Results 1 to 25 of 193
Page 1 of 8 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check