Printable View
I designed and printed a .45 caliber transfer bar and drop tube.
It works perfectly well.
Next I may try to make a top punch.
https://i.postimg.cc/C5KzKwrY/Slide-45-v3.jpg
https://i.postimg.cc/HsckvZfS/drop-tube-45-v2.jpg
https://i.postimg.cc/269C2hTR/C94-C3...05-DBB31-D.jpg
What type filament did you use, i.e PLA?
PTEG.Quote:
Originally Posted by MrWolf
That's what I always use.
I just got used to working with it.
I have a roll of PLA that I may try playing around with.
I want to make some die holders and a .45 bullet feeder plate.
I will try to post the files to Thingiverse this weekend.
I have to start learning CAD AGAIN! Finally found a tutorial I like. I tried using PTEG just before my gf took over my printer area and couldn't get it to work right. Another one of these days project.
PETG is a little more complex to deal with since it is running a higher temp and requires a heated print bed to not warp. Look into PETG + as it has a lot of the same properties of PETG but less hassles.
Thanks. I have the Creality 6se which has the heated bed and I can manually adjust settings. Never knew about the PETG+.Quote:
Originally Posted by ddeck22
Same printer that I have.Quote:
Originally Posted by MrWolf
I run 240/80 for PETG
Thanks. Might give it another try this weekend. I now have the printer setup in a walk in closet. Yea, I know but actually made it work. Put a shelf in above some storage bins and used a dead space.Quote:
Originally Posted by thump_rrr
What CAD program do ya'll use for 3D modeling? I'm in the process of learning FreeCAD which seems to work.
I just got a Crealy 6 myself and use PLA since that's what came with it.
I'm using Fusion 360. It's free to use as a hobbyist.Quote:
Originally Posted by KenH
I've walked away from it a few times out of frustration but I'm starting to get the hang of it.
I had the same problems in trying to to understand the programming. Tried a lot of different tutorials but just got frustrated. Found one made by "Make with Tech" and things finally started to click. I am going back to his videos to refresh what little I learned and to hopefully finish one video. Good luck.Quote:
Originally Posted by KenH
Ron
The quickest, easiest modeling tool is Tinkercad. You can get up and running in about 15 minutes. FreeCad (as you know) has a much steeper learning curve. Of course, Tinkercad has less features, but it is awesome to get started.
I have used Tinkercad up until recently.Quote:
Originally Posted by ddeck22
The problem with Tinkercad is the resolution.
When you try to print something that’s a circle it looks more like a polygon.
I’ll post up a couple of things I printed off of Tinkercad compared to fusion and you’ll be able to see right away what the problem is especially for anything that needs some precision.
The guy I referenced above started by having you look at tinkercad to get you thinking the right way then went on into freecad.
I'd be interested if someone designed the rest of the bullet feeder.
There is a setting called "Sides" on the cylinders in Tinkercad. You can create more sides and that increases the number of sides so that you don't get that polygonal shape. The default is 20, but you can go to 64.Quote:
Originally Posted by thump_rrr
I have and use Autocad everyday in the Construction industry for 50 years, designing and building all kinds of Architecture. But I never hardly looked at 3D. In fact I wasn't that sure it could do it very well. Then I got a 3d printer. Was like starting over.
Not knowing much, I decided to download and tryout Fusion 360.....which was great, but with Autodesk having me for a commercial customer, I could only do it free for a month. Then they wanted to charge my commercial account, a lot of money. So I removed it and started looking seriously at the Autocad I have already. I found it could do anything Fusion 360 could do....what a shock!:) Good thing too, because with Autocad training, I would have to unlearn every Autocad command and start totally foreign commands that were like learning to speak Chinese. But there was still a problem......the bullet collator thread here! Ammo Mike and TylerR and RedlegEd use software just as foreign and incompatible to learn as me moving to China.
They use Openscad, a programmers cad, and DesignSpark Mechanical (both free) to create all the Bullet Collator, and APP files in our Bullet Collator thread. Totally incompatible with Autocad. So I'm in the same boat as you guys.....but learning enough to contribute some.
If you are a computer programmer, do look at OpenScad, but whether you learn Openscad or not, either way look at DesignSpark. It is extremely powerful and free, and even better you can modify, to you own needs, all the files created in that wonderful thread here on Cast Boolits.....it's all about compatibility, so you don't have to reinvent the wheel over and over. I'm absolutely sure that you guys WITHOUT cad training can learn it faster than I can, not having all that Autocad in the brain.
I still print lots of 3d using Autocad, but I can only share the .stl files, which aren't alterable hardly at all. But if you learn DesignSpark Mechanical, that's a whole nuther world that opens up. Check it out, its Free.....and there's quite a bit of online help.
Tried those settings and no go. I have Overture filament. Odd that the test strip down the left side works but not the print.Quote:
Originally Posted by thump_rrr
thump_rrr nice job man.
For 3D modeling I'm using the Fusion 360 as well, I think it's the best tool.Quote:
Originally Posted by KenH
I have done top punches for my old Lyman 45 in PLA - thousands of bullets and have yet to have one wear out. PLA is actually stronger than PETG for parts that aren't exposed to heat.
https://www.thingiverse.com/thing:3978077
https://www.thingiverse.com/thing:3975185
Open SCAD is good for stuff like top punches because you can just change a couple of variables to get a new part.
I have also used OpenSCAD and agree with you, it is another good 3D modeling software.Quote:
Originally Posted by pastera
I used AutoCAD in my student years and I had little experience using it, because, we had classes in descriptive geometry, and later on 3D modeling. But after graduating from university, I stopped using it and returned only when I got my own 3D printer. To be honest, I spent a lot of time to restore somehow the experience of using this program.
And a question related to the thread's topic - have you already experienced these printed parts in practice? What are the results?
If I didn’t just buy a vortex venom for my Walther WMP because no makes a deltapoint pro plate for the pistol I’d try and sweet talk someone into printing me a plate for it. The RMR and vortex plates that came in the box from Walther are plastic.
Me too.....I do not have a bullet feeder for my Star, I cannot purchase it anymore since Magma Engineering is no more, but I have a 3D printer, so is there anyone out there that could design the parts that can be printed?Quote:
Originally Posted by cheese1566
Try using Onshape to make your own parts if you can't find anyone else's files. Finally found a program that I am getting the hang of. Look at the tutorials, plenty on YouTube. I tried it like a typical guy without looking at manuals first. Don't do that and be smart unless you have prior cad experience. I finally dumped the Creality *** and got the Bambu X1 Carbon. Wow what a difference and a pleasure to use. Not a single issue so far and like the AMS (handles four spools at once). I am doing simple stuff so far like making a box and lid to organize my brass and making my version of an Akro burn for nuts, bolts, etc organization so still learning but going much faster now from watching the tutorials. Good luck.Quote:
Originally Posted by hermans
Ron
Edit: Onshape is a free web based software that requires all projects to be public. Private version of course costs but if using it for a business it is the way to go.
Ron, thanks for the advice on Onshape, I will surely have a look at that.Quote:
Originally Posted by MrWolf
My problem is however not the designing of the parts in order to print them, but I do not have any dimensions of any of the parts associated with the bullet feeder.....so I am rather "blind" here. I am currently looking at video's on YouTube as well as trying to find any drawings of the bullet feeder. In my Star user manual there is a rough drawing of the different parts of the bullet feeder, but of course no dimensions, so I have to try and figure that out.
Thank you for the files, and THANK YOU for the scad files. I like having the paraments allowing to change the file.Quote:
Originally Posted by pastera
I have had good luck with PLA+ and it prints just fine.
Can you share the .stl?Quote:
Originally Posted by thump_rrr