Standing 223 boolits for baking

Printable View

03-11-2021, 09:11 PM
Conditor22

Standing 223 boolits for baking

This is easier if you use Silicone Mini Ice Cube Trays 160 Small Ice Cube Molds like CB member Slide previously posted. This way you don't have to make UHMW posts for cutting/punching out the holes, just set the mold on a flat surface, cut/punch the holes, flip them over on non-stick paper, load, bake.

My mind works a little differently than his

BTaT- Trivets https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

Hollow Punch Set, 6 Pc. https://www.harborfreight.com/6-piec...set-67030.html

[ I also use these for cutting/punching lubed wads for BP loading]
https://i.imgur.com/L18W69T.jpg

UHMW plastic (cutting board) cut a small piece 1/2x1/2x3 inch, mark one trivet cavity with felt marker then lightly press the UHMW on it giving you a outline then saw/cut a 1/8 inch post around the mark.
https://i.imgur.com/ImFAiin.jpg

Center the post under the punch on your drill-press and set the stop so you don’t go too deep into the post.
I chose a slow speed then drilled/punched out all the holes.
https://i.imgur.com/rzcsds3.jpg
https://i.imgur.com/HPUbpI8.jpg

https://i.imgur.com/Ky0ultX.jpg

Coat your boolits as usual and sift off all excess PC.

Set the trivet on nonstick sheet , and fill the holes with 223 boolits ��
https://i.imgur.com/yJfVPCy.jpg
https://i.imgur.com/3oIlPuf.jpg
https://i.imgur.com/PYMH9hT.jpg
https://i.imgur.com/UHYA8VS.jpg
03-11-2021, 09:22 PM
Keith Haveman

Where did you get that mat , and how many boolits does it to fill it up . :)
03-11-2021, 09:40 PM
slide

1 Attachment(s)

Here is the one I posted about last month. So far it has worked really well for me. It is good to have options.

Attachment 279401
03-11-2021, 09:46 PM
BNE

Nicely done. Thanks for the idea.
03-11-2021, 10:25 PM
soflarick

I have just begun to dip my toes in PC; is it necessary to stand the boolits up like that?
03-12-2021, 06:54 AM
Land Owner

So 360 boolits at one time. What mold(s)? What Toaster Oven does this mat fit or is that the oven in the house? Expanded wire for cooling? Why are the two sides are not "holed" for boolits? Wider than the non-stick surface below?

I have many thousands of 22 Bator boolits to PC and no experience - yet. These links might be a good fit for me.
03-12-2021, 08:32 AM
Coopaloop86

I use a similar product off of amazon. It was a silicone small ice cube tray. Got 2 for like 6 bucks. Only problem is the powder coat builds up in the bottom and after a few rounds leads to pretty bad PC flashing if you dont dump them as soon as they come out of the oven. No biggie, I either water quench or the sizing die trims most of it off.
03-12-2021, 09:33 PM
charlie b

Quote:

Originally Posted by soflarick

I have just begun to dip my toes in PC; is it necessary to stand the boolits up like that?

It depends on what level of accuracy you desire. Some of us who stand them up are after the best accuracy we can get at longer ranges.

If you are looking for fist size groups at 100yd or less you don't need to stand them. Just dump them in the basket and bake.
03-12-2021, 10:03 PM
Iron369

These are 30cal, but it would work well for just about any caliber with little modifications. https://uploads.tapatalk-cdn.com/202...91cc1ea9e3.jpg
03-13-2021, 08:57 AM
soflarick

Thanks for the tech. Would it be necessary to do that to pistol boolits if searching for best accuracy?
03-13-2021, 12:57 PM
Conditor22

Where did you get that mat , and how many boolits does it to fill it up. === First link in post

I have just begun to dip my toes in PC; is it necessary to stand the boolits up like that? === With most PC’s you get a better finish by standing them up, I have some PC’s that work well with the dump and bake method

What mold(s)? === MP 227-65

What Toaster Oven does this mat fit or is that the oven in the house? === BTaT- Trivets for Hot Pots and Pans, 2 Pack, Trivets, Silicone Trivet, Hot Plate Holder, Trivets for Hot Dishes, Hot Pot Holder, Silicone Trivet Mat, Silicone Trivets, Trivet Set, Trivet Mats, Hotpads measures 6 ¾ x 6 ¾. I used a small countertop convection oven

Expanded wire for cooling? === these were quenched out of the oven

Wider than the non-stick surface below? === optical illusion, the boolits are resting on the nonstick sheet

I use a similar product off of amazon. It was a silicone small ice cube tray. Got 2 for like 6 bucks. Only problem is the powder coat builds up in the bottom and after a few rounds leads to pretty bad PC flashing if you dont dump them as soon as they come out of the oven. No biggie, I either water quench or the sizing die trims most of it off. === You need to Sift/tap all the excess PC off before you bake

Thanks for the tech. Would it be necessary to do that to pistol boolits if searching for best accuracy? === I stand up handgun boolits, they don’t require anything to keep them from tipping over. The further you are shooting and the more critical you are, standing up gives a better finish. For plinking and short-range shooting PC, the surface condition isn’t as critical ---- this also goes back to what PC you are using, there are some PC’s that give excellent result using the dump method.
03-13-2021, 01:58 PM
slide

1 Attachment(s)

Since we are posting ideas here is another option for you guys. I posted this about a month ago. It is on page two of this thread with complete details on how to do it. Also details on the silicone mat posted above.

Attachment 279499
03-13-2021, 05:01 PM
Keith Haveman

Didn't catch that link , thanks Conditor22 . :)
03-13-2021, 08:04 PM
cwlongshot

As always SAGE INFORMATION PROVIDED!!!

Thank you my friend!!

CW
03-19-2021, 12:18 PM
Conditor22

This is easier if you use Silicone Mini Ice Cube Trays 160 Small Ice Cube Molds like CB member Slide previously posted. This way you don't have to make UHMW posts for cutting/punching out the holes, just set the mold on a flat surface, cut/punch the holes, flip them over on non-stick paper, load, bake.
03-24-2021, 08:15 PM
Keith Haveman

Tried the S&B with the new colors , the black did OK , the orange was acceptable , but the purple stuck together like crazy . LOL I like the the way the black turns out , looks kind of like old lead that has oxide .
03-26-2021, 01:13 PM
oley55

Quote:

Center the post under the punch on your drill-press and set the stop so you don’t go too deep into the post.
I chose a slow speed then drilled/punched out all the holes.

^^^genius! I never once thought about using a hole punch in a drill press. thanks
06-04-2021, 01:35 AM
Wolfdog91

Totally need to try this out !
06-04-2021, 07:23 AM
Land Owner

Derivation on a Theme - similar to Iron369's suggestion, I used 1/4 inch "hardware cloth" for 223 Bator and 22-55-SP (RCBS) boolits that works "pretty well" (some of the wires are LESS THAN 1/4 inch apart) and bending was real easy. I also listened to the advice of others here and purchased the silicon tray liner, which I custom cut to fit the trays.

https://i.postimg.cc/zfjM6vDZ/PC_Tray_[2].jpg

https://i.postimg.cc/k4gZmCDV/PC_Tray_[1].jpg
07-31-2021, 10:10 AM
Charlie Horse

Quote:

Originally Posted by Iron369

These are 30cal, but it would work well for just about any caliber with little modifications. https://uploads.tapatalk-cdn.com/202...91cc1ea9e3.jpg

Thanks. A picture's worth a thousand words. Going to try this with some 22's using hardware cloth.
08-06-2021, 01:59 PM
Conditor22

**note** there are a few PC's/colors that you don't need to stand up, they don't stick together if you dump and bake [first make sure you sift off all the excess PC]
08-06-2021, 10:58 PM
jaysouth

Quote:

Originally Posted by Conditor22

**note** there are a few PC's/colors that you don't need to stand up, they don't stick together if you dump and bake [first make sure you sift off all the excess PC]

Share those colors and brands with us, please.