I understand someone on this board has a line on a good cannelure tool. Can someone lead me in the right direction?:?
Printable View
I understand someone on this board has a line on a good cannelure tool. Can someone lead me in the right direction?:?
chuckbuster "Ultimate Cannelure Tool" I don't know if he still makes them. I own the wide model #091 with additional tooling.
One of the many happy purchases I have made from folks on this site was the Ultimate Cannelure Tool which was made by "Chuckbuster". I also purchased his accessory wheels :). This replaced :) :) :) my C-H tool. Tis hard for me to believe that I purchased mine on November 24th, 2014! Attachment 323451
As above post suggested, I, too, do not know if these are still be made. However, manufacturer/seller gives new meaning to "straight shooter" :) and his eMail address -- the "real one" a decade back, was chuckbuster at hotmail dot com . You might try it?
Good luck! Again, if you can find one -- imho, there's none better!
geo
I have the C-H tool. Don’t know if they are still in business. I use it on 10mm/40 cal bullets for 38-40.
I did a search and found a website
https://chtoolanddie.com/
2023 CH Tool & Die. All rights reserved.
here is a link for the Cannelure tool. and it says to call for availability
https://chtoolanddie.com/products/bullet/CanToo
in general for ordering the site says
HomeCustomer Service
How to Order
Until we get the online ordering system up and running, the best way to order is via email. You can call if you like, but the phone lines frequently back up and you will end up having to leave a message anyway.
So for now:
Make a list of part numbers you are interested in.
Send us the list via our contact page.
We will email back and forth to discuss availability, prices, and shipping.
When everything is ready, you can call with credit card details, ask for a PayPal® invoice, or send us a check or money order.
I see this is in reference to a tool for canneluring BULLETS,...but has anyone ever made a tool for canneluring CASES? Cannelured cases were common decades ago. You used to see them usually in .45acp, .38spl, 9mm, .45colt and such. But you almost never see them anymore. I like how newly cannelured cases can help to prevent bullet set-back within the case, which can be very important for straight-walled cartridges in self-loading actions.
Attachment 323515Attachment 323516
Does anyone make a tool specifically for rolling lube retaining checkering on the exterior of smooth sided boolits?
When I started sizing Jacketed .357 Bullets to .351" for my Winchester model 1907 a guy on a news group (190's) told me to try the Lee Factory Crimp die for 38/.357 . It works like a charm to make the case indent on the bullet jacket.
I purchased this option with my UCT, and albeit I only used it once -- more "playing around" than for any specific cartridge, I recall noting that results varied if different brands of brass were used; and, trim length had to all be right on. I had thoughts to annealing brass first, but never got around to it. My purchase of the optional roller was 99% more of an "OCD -- I may need it someday -- so, why not?" purchase.
On the other hand, as writ in earlier post, there are no words I'm aware of to voice higher praise for the Chuckbuster tool. I have mine fastened to a 1/2" thick Plexiglas rectangle relying upon C-clamps to mount it as/where I wish -- and it has alway been a pleasure-plus to use! My one and only regular complaint -- which is pretty much "all me!" is when I, say cannalure 100 bullets, I can almost guarantee I will be picking 10 or so up off the floor. So regular an occurrence I always put a plastic dish-wash container on floor when I do this -- to catch them! Again -- I do my canneluring with oil lub -- and hangin' onto those cannelured bullets can, for my fat fingers, be a challenge....
geo
The only cannelured brass I see with any regularity is 38 special and occasionally 357 mag. And the varying distances the cannelure is from the case mouth makes it doubtful the purpose is to prevent bullet setback, unless the cartridge is cannelured after loading, to form a crimp ring through the brass indenting the projectile.
Some Remington 38 special has a cannelure 1/8 inch below the case mouth and the bottom of bullet is set well below that. I could see how the depth of case cannelure shown in post #9 pictures may keep the bullet from setting back. And also cause a weak spot in the case. Factory loaded 38 wadcutter brass typically has a cannelure indexing the base of the bullet. Even that pretty much vanishes for any useful purpose after one or two reloads. I’ve tried feeling the cannelure inside the case with a dental pick, there isn’t much left, least-wise enough to restrict the rearward movement of a bullet, let alone provide a stop when seating a bullet.
Just my observations.
According to >outpost75< the purpose of the case cannelure on .38 Special and .357 was to locate the bullet upon assembly, since smokeless loads could not do so. The case was sized down and crimped in a subsequent operation.