Thank you, that's definitely more than I knew before!!!!
Printable View
Thank you, that's definitely more than I knew before!!!!
I have accumulated these 310 dies over the years and have never used them or have a need. I want to move them along to someone who collects and/or uses the 310 and hopefully one of you are interested. My primary goal is to get them in the hands of someone that will enjoy them and get something in exchange I can use. I would swap them for LE Wilson trimmer and/or case holders or RCBS dies and/or die parts. Pretty open. If you have something you want to move along, run it by me.
Bottom to Top:
Left Column:
#2 shell holder
429 Seater w/421 stem
Decapper minus pin
Right Column:
153 Seater w/450 stem
266 Expander
287 Expander
Attachment 216759
Left column #2 is a #2 priming chamber. It fits the -06 case head, large primer, which is probably the most useful priming chamber they made given the variety of cartridges that use this case head, including the 45ACP.
Thank you Wayne. I have never used a 310 and relying on some research. You are correct. It will fit all -06 based cases including all .308 based cases as well as .45 ACP. Way too many to mention them all. I hope someone here wants them. I am more interested in getting them in someones hands that will use them than anything.
WTT Have 310 44-40,45acp,38spec dies. Sizer ,seating & priming 30-30 dies Also 32special size and 2 seating dies for trueline press. 2 hand sizeing dies 1 30-30 and 1 32 special. 2 handles 1 lg 1 sm. 1 45-70 priming die. Looking for 35 Remington mould FN Rcbs or similar,32-20 brass,25-35 brass and bullets. 38-40 mould that casts a bullet .403 dia. or larger. My 401 mould is to small. Also need a receiver sight for 336 Marlin.
These dies are still available for trade.
As has already been stated, the No.2 Primer Seater will work with any rimless cartridge with the same head size as the .30-'06. The tool No.429 with No.421 plunger is a bullet sizing dies (0.429 diameter), and the plunger is designed to fit the nose of the Lyman No.429421, and is used to size the bullet base-first using the plunger against the nose (as when sizing with a bench mounted lubricator/sizer). Die No.153 is a Double Adjustable (aka Bullet Seating) die for the .270 Winchester. The No.450 Seating Stem is designed to fit the Lyman No.224440 bullet, but likely also will work with some other projectile suitable for use in the .270.
Jim
Does anybody have a spare priming chamber (PC) #10 they could swap or sell? Please answer here or with a PM. TIA!
Froggie
Thanks Jim. Way more information than I was willing to dig around for. I'm really hoping someone can use or appreciate them. I am more interested in getting them into the hands of someone that will use/appreciate them than what I get in exchange. Where they sit now, they are of no use.
Looking to sell or trade 2 tru-line presses, small alloy handles, 310 dies- 222, 7x57, 30-40 krag, 38/357. Getting out of tiny dies
Speaking of 32 S&W, who has a spare 310 set and what do I need to trade for it?
I probably could put together a set if you can't find one elsewhere. I need to keep a set for my 310 and one for my TruLIne Jr (dedicated) but if there are enough left over parts I'll let you know. Would you be interested in a couple of the dies to start building a set??
Froggie
Well Magnet Man, somewhere between the event horizon and the actual black hole in my basement there should be some boxed sets classified as trading material. I had the previously mentioned TL Jr boxed set for 303 Brit as well as a backup set of 310 dies for 32-40 and another for 32 S&W Long. Organized people don't make the exciting discoveries I do, but at least they can find what they actually have when they need it! [smilie=b:
Froggie
Still needing 32 S&W and 32 S&WL dies for 310 or TrueLine Jr. I even posted a WTB in S&S!
All I've found so far is a spare 311 expander die and maybe a spare #9 PC. I've gotta get organized (maybe next year! :roll:)
Froggie