yep thats what I'm working on,I started with a small guide rail under the pot then over to the vise with wood blocks to hold the hot mould.,I may have to chang up to a master casters it's one hand opertaion.
Printable View
yep thats what I'm working on,I started with a small guide rail under the pot then over to the vise with wood blocks to hold the hot mould.,I may have to chang up to a master casters it's one hand opertaion.
Could you use this one handed for casting? You might have to scroll down the page a little to see the spring laoded mold handles.
http://www.castingstuff.com/cabinetr...g_products.htm
The other solution could be getting a master caster, you can get other 2 cavity molds converted to use with it. I think the master caster would be a large initial investment, but you would have something off the shelf.
Mould opening:
A tube flattened in the end
http://i295.photobucket.com/albums/m...e/R0010616.jpg
Insert sprue plate and twist
http://i295.photobucket.com/albums/m...e/R0010617.jpg
http://i295.photobucket.com/albums/m...e/R0010618.jpg
Here's the "pedal" for the press (obvislly a mock up!)
http://i295.photobucket.com/albums/m...e/R0010619.jpg
http://i295.photobucket.com/albums/m...e/R0010620.jpg
I use a net to catch my brass at the firing line and have an attachment which fits under my grip for work off the line. The grip catcher does not allow proper holstering but it shoots fine. Those wire frames for the political adverts hold a mesh laundry bag for the bench version. I have seen a lot of stands for them but dropping the wire through a PVC pipe end cap (drilled for the wire) works easily and you can add shot or lead to the pipe fro a stand.
Check with Chris Smith at redgreen@cooldude.com. He made top punches for me with great turn around time and excellent quality. He can probably machine one with a hole and a hex screw to hold your Lyman/ RCBS top punches. But you still need the sizer die for the star.
how about one of these...
http://www.uniquetek.com/site/696296/product/T1310
pretty slick brass "picker upper"
ww
Hey, wymanwinn, that looks pretty slick for developed public ranges! One of the problems some of us have is we don't shoot at a range with paving or hard ground. The place I go is in the boonies, so out in the weeds and loose dirt a brass catcher that works integrally with the firearm is the only way to recover brass. Finding just one case in brown grass is a problem without a metal detector!
rl 1088
wymanwinn
I have one of those brass buddies but after I get about 20 9mm shells in it, I lose as many as I'm trying to pick up. The wire is simply too thin and I'm going to try build one with wire about .010 thicker.
A good way to store dies with Hornady LNL bushings on them. I have a ton of empty die boxes because they won't fit in there.
In bulleye pistol matches they have a free standing brass catcher that works pretty good. I have made several. Sits on the bench beside my hand accross from ejection port and catches brass with out being attached to the gun or me.Look at Champions Choice or possibly wilsons. Set up right mine will catch 99% of my brass normally.
Every time I see the price for a heater for the Lubrasizer (I'm only talking Lyman here - no trials on RCBS) I about have a fit. I have a plan for us all. Find a clothing iron - yea, what's that - buy new at Ollie's or Big Lot's for about $10 or so. Now, get a piece of flat aluminum plate about 1/8" thick or a little thinner (it's not critical - even thicker won't hurt) that will fit completely under the Lubrasizer and the iron too, right behind the sizer. You will be limited to the width between the sizer's mounting bolts but, more is better and I have chosen to drill through the aluminum to get a little more width and more room for the iron to transfer heat. The iron doesn't even have to breathe hard to transfer its heat to the sizer. Total invested: $10 for the iron. All else was scavenged. Good luck!
Later,
Chiz
now that is slick
I built one in my shop, it is 2 feet wide and 4 feet long. the frame is 2x4 and the top is particle board(for the time being, I am making a new top out of ash). My bench has a back(peg board) with a shelf on top, under the shelf I have mounted a twin bulb fluorescent light. In the back I mounted a power strip with 6 outlets. The top is recessed into the frame and I added a shelf on the bottom. I used premium wood glue and pocket holed all the joints. All in all, when I got finished I had a bench that can be a part of the furnishings of my home. Here is mine, and yes that Hank Jr. watching over my stuff. My casting bench is still out in the shed where it is gonna stay.
The total cost.....$47.00
The total time....about 3 hours(give or take)
I bought most everything on clearance at Lowes or Home Depot. Also if you have any Habitat for Humanity stores in your area, you can help them fund the charity by buying from them. If you can take your time and shop around you can find a lot of good deals.
You mean like this only cheaper and more widely available?
http://www.meachamrifles.com/page.php?id=73
I would like to see someone simplify this fellows design, and hopefully make it cheaper.
However, in the meantime, I think tumble lubing and lee sizing will work for me.
I built a ladle from a scrap piece of 2 1/2 inch pipe. I used an old bottle top from an oxygen bottle, cut out the top and welded to it. Used a piece of tubing to make the handle. I have about $3 in it plus my time....30 minutes. It holds about 2 pounds of melt, works really nice.
How about something like this, laser cut holder for Lee turrets
http://i226.photobucket.com/albums/d...ps617b4852.jpg
Final version of the turret holder
http://i226.photobucket.com/albums/d...ps369453ce.jpg
I saw a guy last week at the range who had a stand with a rectangular net at the top. It was about 12" tall by 18" wide. He was shooting several hand guns and catching all his brass in the net. I looked like the net was fairly fine mesh made from cotton (I *** u me). I've been thinking along those lines ever since