http://i16.photobucket.com/albums/b1...pse0d3f07f.jpg
Printable View
This is one of my trays for HP bullets the thumb tacks are held in place with PC I just used some overspray to glue them in place. I did make one using sheetrock nail that are more like a large tack and did them the same way but after the build up of powder it failed me after several trips to the oven.
http://http://i244.photobucket.com/albums/g...ps24fc27b3.jpg
These were sprayed with HF yellow and they are the mehic molds for my 9mm.
Attachment 118827Attachment 118828
I filled up my convection PC cooker with pinks Thursday night. First picture is oven sitting on the back of my quad outside the walk in basement slider. Second is trays after the cook in my basement work room. My three trays will hold 714 projectiles with 3/4" spacing. I made a loading jig out of a piece of 1 X 12 pine, into which I load boolits nose down then I put the tray on upside down, flip over, PC and cook.
Nothing accessorizes a Mauser like pink!
http://i613.photobucket.com/albums/t...psf173c76f.jpg
Here's a few pics of the ones I made for a USPSA sectional we had in NC last week.
Attachment 118864
Attachment 118865
Attachment 118866
Those are both Mihec molds I cast with; one was 125gr hp, the other was 135gr. I used Power Pistol, and got 148 power factor.
And here is the results... I shot about 250 pc bullets in the whole competition.
http://youtu.be/ERlEjFI9taA
Screen covered racks that came with oven
Attachment 118927
Wood jig that I load non HP boolits on the rack above after putting NSAF on it
Attachment 118928
Pop rivet through aluminum plate rack for nose down HP's
Attachment 118929
Nose down rack for 300 using BO cases and silicone grommets for .225's
Attachment 118930
Picture of 3 racks of 9mm 125 TL Lee total of 714 boolits was in my earlier post
What they looked like as they dropped from the mould:
http://i60.tinypic.com/2rfy41v.jpg
After powder coating (tumble method) and sized down to .311
http://i60.tinypic.com/ws3dps.jpg
The result of my FMJ load of RL7 @ 25yds thru my Yugo under folder
http://i58.tinypic.com/35jzg9f.jpg
This should be one of the questions in the FAQ....
But there's too many pages to read in the whole powdercoating section to find all the reasons....:coffeecom.... so here goes my try at it:
My whole purpose for PC was to be able to shoot some nice soft lead in pistols faster without leading than before. And range lead is cheaper to buy and easier to find than wheel weights. It lets you avoid having to handle sticky boolits, it doesn't gum up your loading dies; it provides really long term storage without oxidation of your boolits, or the lube drying/cracking or melting out of the lube grooves; it makes pretty boolits (unlimited colors), it allows you to color code your loads if you want to separate hot from plinkers, etc.; it doesn't smoke when you shoot it (the indoor shooters like that), and it is much cheaper than any used lubesizer you will ever find. :cool:
It also lets you store loaded boolits without any fear of long term powder contamination from lube and it allows you to shoot gas check boolits a little faster without the check than you could shoot them with lube. And within limits, it also sizes up boolits that may be just a hair too small.... making some Lyman and Ideal molds give people the size boolit they were looking for, without having exactly the perfect alloy and the perfect temp for both mold and lead every time they cast.
Other than that... it is not a gas check. It does not protect the boolit from gas cutting. It does not improve velocity, obturation or expansion (it does not keep hollow points from expanding normally). There is much debate about how it affects accuracy, either good or bad. That seems to be up to the individual.
Since this is a pic thread, here's a pic of some .45's that I tumbled in Smoke's green. It's fast, it's easy, it's cheap, and they leave the gun and dies clean as new when you're done!
http://i613.photobucket.com/albums/t...psaf8ad3e7.jpg
And here's some Hornady swaged .45 bullets that I tumbled in HF red..... they aren't sticky, they load up clean and shoot great.
http://i613.photobucket.com/albums/t...ps3b4a0207.jpg
NOE 360-230 RD in Smoke's purple.
http://i613.photobucket.com/albums/t...ps3a13557a.jpg
Cast a few 148 grain wad cutters for the 38 special, powder coated and installed home made gas checks on plain base cast bullets.
The gas check material is .006 thick aluminum roof flashing.
There are 500 bullets per tub.
Cast on Automated Master Caster Machine
These bullets result in a very clean barrel after several hundred shoots.
Attachment 119962
My 2nd attempt. 40 S&W. Carolina Blue from Smoke.
http://tapatalk.imageshack.com/v2/14...58e6dd87d3.jpg
Basket of 44
Lee
.429
Wght 240gr
First cast for a range Buddy
NOE 402 160rn aluminum 5 cavity
Before:
http://i1112.photobucket.com/albums/...194227_866.jpg
Powder from Smoke. BBDT method. After:
http://i1112.photobucket.com/albums/...203359_024.jpg
My first try. Coating isn't 100%. Not sure why certain spots on the bullets didn't want the powder to stick.
Lee C309 170grn.
Super Durable Matte Black
BBDT
Toaster Oven at 400 for 10 mins.
http://i1001.photobucket.com/albums/...psca4189d7.jpg
http://i1001.photobucket.com/albums/...ps2944708b.jpg
Played around again with my new RCBS 7.62 mould but this time sized them to 308
http://i57.tinypic.com/2mqndrq.jpg
fired thru a FAL only at 50yds using a FMJ recipe
http://i58.tinypic.com/2i8d3ly.jpg
surprised that 90% weighed exactly 139.5gr after powdercoat and gas check
Attachment 120201my first powder coating
Images