hey, thanks for video's, shows how simple & easy to coat.
Printable View
Have a look at the two U-Tube videos, link attached below , to demonstrate how the coatings can be used by even hobbyist. Joe
YouTube videos:
Part1
https://www.youtube.com/watch?v=VevKJgHseWc
Part2
https://www.youtube.com/watch?v=NU7PbbtbAtE
can you tell us exactly how many ml or cc of hardener,color and acetone used per 500 bullets??? thanks just want to make sure i mixed them right...thanks...
Hi,
Thanks for contact.
I assume that you have obtained coating from Bayou. Is that right?
If you have the dark Green, simply put, for every 5 litre of coating, you need 1 litre Catalyst.
When coating projectiles, the 5 litres with catalyst and dilution solvent, should coat between 35,000-50,000 projectiles per litre.
Manufacturers, use small amounts of coating, mix with Acetone to dilute coating, and add Catalyst.
Example, 100mls coating, add 150 mls Acetone, and 20 mls catalyst. Mix, then add about 20-25 mls to 1000 projectiles of this mixture. Tumble coat, just enough to coat all, and then pour out and dry well. When dry, bake at 190C for 8-9 minutes in an oven that has very good air circulation inside it.
I have attached two U-Tube videos that was made by user in US. You need to look at them and then realise what is needed.
You will need sound and you get instructions on how it is done with continuous movie.
Let me know how you go.
The Catlysed diluted mixture can be used for 2-3 days, it is better to keep it out of sunlight and below 30C, possibly at 20-25C.
U-Tube videos:
Part1
https://www.youtube.com/watch?v=VevKJgHseWc
Part2
https://www.youtube.com/watch?v=NU7PbbtbAtE
Joe
thanks for the reply.. yah i got it from bayou bullets. im just coating in small batch like 500 bullets ..
Ummm. I shoot cast from my glock 19 with no issues. Slug your bore and go 2thou over. I use a lee 358-125-rf sized to .357 with 20:1 alloy and a 60/40 wax lla lube. I have to rapid fire for a mag or 2 to get any issues. I send a plated or jhp down every 2 or 3 mags.
It seems to me, that firing Alloyed Lead in your glock still is producing Leading.
Your way of fixing problem, is to shoot Jacketed or plated projectiles to clean the gun.
Just a couple of observations,
1. You are still getting Leading of the barrel.
2. Shooting jacketed or copper coated projectiles will not remove Leading completely. Further, Copper will deposit onto the barrle, which needs very agressive cleaners to remove, which may also damage bore with pitting corrosion whilst dissolving the deposited Copper.
In Australia, they have used the HI-TEK-LUBE coated Alloyed Lead in glock for many years, without any such problems.
It is only in recent times, since introduction of the coatings to the US where it is now being found, that simply you do not need Jacketed or Plated projectiles, and you save money by using coated Alloy.
Just enquire with Donnie at Bayou about test results.
If you are using very small quantities, it may be a problem to measure out tiny amounts of ingredients.
I always recomend, that you prepare a batch of projectiles in advance, say 1000-5000 and then measure out the amount of coating required, (generally in volume relationship).
To coat 1000, for example, if you use 30 mls coating, 30 mls Acetone, and 6 mls Catalyst, this should coat the 1000 with two coats, with possibly a little left over, (a few mils.).
If you are coating less, than you need to adjust down the volumes accordingly.
Did you see the U-Tube videos? It tells you every thing you need to do.
Many, use plastic Syringes to measure out volumes, (10mls, 50mls sizes, or as required.)
Joe
Hi, I was told by one of my customers, that they have shot projectiles with our coatings at 3000ft/sec. I did not get any other details.
I suggest, that if you are going to shoot at that speed, the coating needs to be well cured to obtaine maximum hardness, generally at 195-200C for 8-10 minutes.
You will need two thin coats, covering projectiles to ensure that surface of alloy is covered.
Maybe this was all ready posted, but better share it twice ;)
Here we will get the recipe!!!!!!!!!
https://www.youtube.com/watch?v=uQ7M...0BF3FA8392B831
I searched but found only 2 posts on the issue of 223 bullets and these coatings, both where questions if it had been done. I'm asking the same thing. I'd be interested to know if you can coat a 223 bullet and have it work properly. Could one skip using gas checks then too perhaps? Perhaps even a plain base (or boattail) lead bullet could be used then?
HI-TEK,
Based on the durability of the coating, it sounds like I should be able to use soft lead and not get leading (in a 9mm for example). Have you heard anyone doing this successfully? With lead wheel weights drying up, this would be huge.
I think wiederlauderTV is optimistic if he thinks he can get 25 million views. I wonder if there are 25 million casters in the world, let alone the subset who also want to lube/coat using his coating. He might want to lower his expectations by a factor of 10 or more.
So, I wonder how this coating would affect hollow-point performance. Do you think it would tear, or stretch with expansion? Would it possibly help penetration, and control deformation?
I had already seen this post on coating projectiles.
I do not know who is responsible for rhe video.
The coating information is freely available from J&M Specialized Products P/L on
jandm@blue1000.com.au. Coating is also avaliable from them also.
J&M invented the coating about 20 years ago and have been selling it to all and supplying technical back up and free assistance and customer support.
Attached below, is two videos made in USA, by a hobbyist where the coating process is displayed.
YouTube videos:
Part1
https://www.youtube.com/watch?v=VevKJgHseWc
Part2
https://www.youtube.com/watch?v=NU7PbbtbAtE
Videos are free without strings attached.
The coatings have been used for quite some time with all types of projectiles.
In reference to deformation properties attached is a picture of what can be achieved with coating.
Old Bronze+Dark Green Attachment 61446
I thought, that this would be useful for you to know about the properties of our coatings. These are two of the Hi-Tek-Lube Supercoats used to coat projectiles.
Left to right, Old Bronze, (new Colour) and Dark Green.
These projectiles are coated and baked with two very thin coats.
The above tests, are typical test results obtained with the coatings, when the coated projectiles are subjected to extreme deformation.
Note that flattened projectiles, one side is rough where it lay on the concrete when flattening, and coating, despite being severely damaged stayed put on surfaces.
Surfaces, that are smooth directly alongside, is where 8 pound hammer hit surfaces, which are flat and smooth.
No fracturing can be seen on damaged surfaces.
Sizing projectiles to correct diameter after coating, allows exact finished diameters to be produced, and no lubricants are required to size or to shoot with majority of applications.
Due to the extreme beneficial properties of the coatings, it stays put on alloy, even with use in most hostile applications to prevent Lead becoming in contact with Barrel.
There are many attempts to reproduce such results, and I have seen many, with just as many concoctions trying to invent the ideal coating/lubricant.
A million shooters cannot be wrong, and people who continue to use our coatings.
wiederlauder TV video certainly appears to be suspicious in intent.
The Coating, that is shown, appears identical to the HI-TEK-LUBE coating used by many world wide already. The coating & information, is freely available from supplier and manufacturer J&M Specialized Products P/L, and no strings attached.