Did you flip a press over just for sizing? That looks genius.
Printable View
Loaded some step loads for 223 to make up some 22 mag or less loads but I don't think I can get there the 225-37 NOE ...........
Knocked out some loads that should be subs in the 1895 .......... Not having much luck with that ..........
Super heavy weights didn't work out in the Colts rifle any better so I don't guess I should be surprised .
It's 95° now so maybe when the sun gets behind the hill I'll go try these . I'd hate to have a load get stale . :)
Tomorrow is here and just finished smelting 215 lbs of free pure lead in to ingots. That was a bit of work.
Loaded 50 pounds of shot into shotshells for a few weeks fun
Mike
Busy day for me.
- Decapped and wet tumbled 550+ pieces of 308 brass.
- Sized 1,500 pieces of 300 Blackout and wet tumbled half of 'em.
- Sorted half of a 5 gallon bucket of brass that I bought. LOTS of 44 SPL/Mag in there.
Spent a lot of time working with the the Lee 358-158-RF mold I used making the ugly boolits. The mold release was cleaned out of the mold and then I scrubbed it with Dawn and hot water followed by a final cleaning with lacquer thinner to remove the remaining bits of mold release. I went over the edges of the troublesome cavities that prompted me to use the mold release to begin with. I found a few burrs and scraped them off. The mold still needs a whack or two on the hinge bolt at times but it's much better. I slowed the pace, lowered the melt temperature and went from the ugliest boolits I think I've ever cast to nice ones.
Attachment 202223 Attachment 202224
just finished turning 300 40S&W brass into 250grn 44mag proj.
Yeah...thought you knew...http://castboolits.gunloads.com/show...n-Sizing-Press
Learned that I loaded up a way too hard of a boolit with trailboss after watching loads of bacon.
Gonna use my 7.5BH batch that was so pose to be 16:1 to cast up some more devistators to use instead of the current 14.3BH boolits.
I bet these hard guys penetrate!
Attachment 202228
These HP's have their cavities filled with silicone white caulk to act as penetrator tips, non clogging HP's...
I might have to try that!
Wouldn't you think the hard HP would cause more trauma trying to tear through soft flesh?
I keep think of slapping my mouth with the flat part of my hand and hearing a pop and multiplying it by a thousand.
Maybe I'll superglue a airsoft BB like originally planed.
The other thought I had was like the movie "the bear" where one of the hunters made an "x" with a knife, I believe it was a 35 Rem, to get it to expand quicker. I would think that would make a harder boolit fragment with similar results as a nosler partition.
BTW...how many more posts till I get my 1st boolit?
1000 post per boolit
So you have 1000-390 = 610 more posts till you get
your 1st boolit
Mike
Just casted 10lbs of devistators with a BH of 7.5 and found out my new replacement mold is leaking around the HP pin area like the last one.
Attachment 202268
Should get some low velocity mushrooms now!
I think the silver ones are @ 1,000 posts and gold @ 5,000...not sure.
Mold could be too hot. I let it sit on my Coleman burner to stay warm and heat my pin between casts.
I thought if my lead or mold was too hot the boolits would be frosted which none are.
Attachment 202279
I PC and GC a few
Well, not exactly today, but I finished it off today, 56 pounds of 9mm brass run through my roll sizer, and it is not automated. Worst part it's not my brass, belongs to a reloading buddy of mine.