http://i798.photobucket.com/albums/y...psuwkyemvy.jpg
Nice Group Brad, here is my best so far, 240 gr XTP over 14.5 gr of 2400. Only about 15 yards but thats real good for me off hand in the snow...
Printable View
http://i798.photobucket.com/albums/y...psuwkyemvy.jpg
Nice Group Brad, here is my best so far, 240 gr XTP over 14.5 gr of 2400. Only about 15 yards but thats real good for me off hand in the snow...
That's fine shooting in my book! I want to try some 2400 in mine too. I feel alot better about mine after getting it back.
Any leading issues?
No but understand I have firelapped it and recut the forcing cone. It actually shoots really nice now. A definite favorite.
I also forgot to mention that I shimmed the wiggle out of my rear sight. It had .017 clearance in the slot so wiggle it certainly did, a lot...
Looking good. Thanks for the couple of updates.
Sent from my SM-G930P using Tapatalk
I just spoke with a very helpful fellow from Ruger. He called to let me know that my gun had been received and would be getting a new cylinder and barrel. The new throat spec is .431. Barrel is being replaced to correct front sight gap.
Sent from my SM-G930P using Tapatalk
Got a UPS tracking number today. The gun is on the way back. I should have it Monday.
Sent from my SM-G930P using Tapatalk
Well I just got mine today, wish I would have read all 16 pages before I looked it over; I will be calling Ruger this week. I checked the cylinder and it has .431 throats, no noticible choke in the cone but leading with some cast bullets - fired everything I make/made 200-265 grain SWC and everything shoots to the right; even at 10' it shoots 5" right with the rear sight all the way to the left. Took a good look at the barrel and it is noticably overtorqued to the left.
The PRO's - the trigger as as good as my match champion, fit looks good (gap between the top of crane and the frame but not horrible,) B/C is .007, cylinder looks more consistent then most .431-.432. Locks up tight and feels really nice in the hand.
Cons - Barrel is off, leading and their is what appears to be a gap between the frame and the barrel threads.
I was hopping all this was behind them but I must have gotten a first run. I still have high hopes, I have not had the issues with most of my Rugers that most have (still out on the .480, need to replace the sight.) All in all the last 5 or so guns I have bought have been pretty good. 2 - Lypses .44 spl, Match Champion, two .41 mags, a .22/.22 mag and 77/44 rifle.
I thought bad about the MC but after shooting the heck out of it, I have found that it just one of those guns that is picky about its loads; likes its cast at .357 125-150 grain.
Powersgt
I have the repaired firearm back in my possession. UPS dropped it off about 45 minutes ago.
The cylinder and barrel have been replaced and the gun looks exceptionally nice. It had a small scratch on the top strap when I sent it in but it has been polished out and the gun looks brand new again.
There is still a small gap underneath the front sight but it is only about the thickness of two pieces of paper.
Included is a printed copy of the test target.
https://uploads.tapatalk-cdn.com/201...16ee8d12be.jpg
Cylinder throat measurements, using my small hole gages, indicate four throats at .431 and one throat at just a smidge over. Probably. 4315 with more precise calipers. Furthermore a cast bullet sized .430 passes easily through while a cast bullet sized .432 does not. I don't have any sized .431 currently.
Here is the gun with some Pachmayr Compacs I scored off eBay. Sorry if I outbid you...
https://uploads.tapatalk-cdn.com/201...5cb23c5cd2.jpg
Sent from my SM-G930P using Tapatalk
Lookin' good!
Hope it works out for you.
I'll try to get some rounds fired this afternoon. I still have a few odds and ends that didn't shoot well in the gun with the original cylinder. Fingers crossed that some (or all) will shoot okay now.
Sent from my SM-G930P using Tapatalk
I plan on trying out various cast and coated bullets for my refurbished GP100 44 Special. I recently received a sample pack of 25 polymer coated 240 grain SWC .430 bullets from Bad Guy Bullets. These bullets drop right through the cylinder. I am interested in a load that comes close to the original old factory load. May order a hundred of these sized to .431.
http://pic20.picturetrail.com/VOL161.../413168925.jpg