Printable View
Is there a decent market for revolver stocks or stock kits? For single action guns like Blackhawks or pietta/uberti reproductions. I looked online it seemed like only a few people are making them. And no one I found for remington c/b. Mostly colts and ruger stuff.
Sent from my SM-J337VPP using Tapatalk
Nobody seems to make quality replacement grips for the current medium frame flat top Ruger Blackhawks. I would like to find some nicely checkered walnut grips which are a bit fuller than the factory black plastic stocks, but not bulky for ham hands.
Something which approximates original turn of the Century, pre-1920 Gen1 Colt grips which have not been slimmed down. Nice feel which can handle the recoil of full snort .357 or .45 Colt, but not oversized and bulky like too many modern grips.
The Uberti and Pietta grips on the Cimarron and Taylor & Co. revolvers are close, but I would like replacements in better wood with fine checkering for grip, but not so sharp it scrapes the hide off. British - style flat-top diamond checkering of about 20 lpi would be wonderful, with choice of ebony, rosewood, ivory micarta or a quality wood-grained synthetic approximating figured walnut for under $100 would sell.
Similarly, quality replacement service stocks as direct replacement for S&W Magna with raised diamond around the screw eschuteons, for N and K frame, round bottom "plain clothes style, and faithful copies of service stocks for pre-WW2 Colts, Army Special, New Service, etc.]
Outpost75-
For blackhawks
So wider in the middle portion of the grip? Vs the current kind of tapered wider out towards the bottom of the grip
I wonder how difficult it will be to get ahold of a original gen1 colt set from that time period.
And for s&w N,k frames basically a wooden version of this rounded grip? Only with the diamonds around the screws as you mentioned.
Sent from my SM-J337VPP using Tapatalk
https://uploads.tapatalk-cdn.com/202...39d3e49440.jpg
Yes, but measure some post-1900, but pre-1920 original Colts.Quote:
Originally Posted by johnsonian09
Check Badger Custom Grips!
Smithnframe- I'm thinking about making grips for SAA/ CAS type guns. Badger customs does go beautiful work though. It's nice you can select what blank the grips are made from too.
Sent from my SM-J337VPP using Tapatalk
Actually, there's a few makers out there, but you may be looking for the wrong thing.Quote:
Originally Posted by Outpost75
The newer Ruger Flat Top revolvers take the same XR3 grips as the Old Model Blackhawks, instead of the XR3-RED grips.
Ruger usually casts the SA grip size into the grip frame casting below the mainspring, visible via removing the grips.
https://i.imgur.com/vkezGBQl.jpg
Many of the imported Colt SA clones take the same grips as the original Colts, except for those companies that chose to make a different size/shape grip frame for their clones.
I think I have a set of black, gen 1 saa grips around here some where. They were in a box of parts I got from my dad when he passed. If there is interest, I can go digging around for them.Quote:
Originally Posted by johnsonian09
The nicest aftermarket grips seem to be Eagle. Way too spendy for me. I have been buying grips from Altamount. They make good usable grips from what they call super wood, they laminated birch in Walnut or Rosewood colored. Have several sets and am happy so far GW
I'd like the set to make patterns off of it if you could find them
Right now I'm making a small run of 1858 grips from spalted tamarind and lace-wood
After I finish these I'm going to try some walnut and do some checkeringhttps://uploads.tapatalk-cdn.com/202...71a0272ae5.jpghttps://uploads.tapatalk-cdn.com/202...2890fef860.jpghttps://uploads.tapatalk-cdn.com/202...d6855c2a4e.jpghttps://uploads.tapatalk-cdn.com/202...b231d3fa18.jpg
Sent from my SM-J337VPP using Tapatalk
Oh my.... Very nice!
SA grips are not hard to make. I rough them out with a jig saw and shape them with small drum sanders on a drill press. Takes about 2 hours to finish a set.
Some years back I bought a quite "pre-owned by many" ;) SAA which came with a set of cracked plastic "stag" grips. Seeking replacement, a friend offered me a large box with -- maybe 100 or so? -- loose grip halves in it. It took me quite the expenditure of time to pair the lefts' with matching rights', and by pure happerstance tried a similar-looking pair, to -- after closer examination -- noted the left grip is substantially THINNER than its matching right grip!
It's "fitting" is almost like magic. Such that on my (obviously newer) Vaquero .45 (old model) I have a piece of cut leather stuck to the right grip's outside.
Just something that really works for me. If contemplating new (custom?) grips, this is something you may (or may not :)) wish to try.
BEST!
geo