RepackboxRotoMetals2Lee PrecisionADvertise here
Reloading UKTitan ReloadingInline FabricationMidSouth Shooters Supply

Donate Now Goal amount for this year: 6000 USD, Received: 3065 USD (51%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


  • barrabruce's Avatar
    Yesterday, 07:08 AM
    I have a hundred ness bullets to use up with the big pins. I haven’t found it’s Sweet Spot yet with the big hollow point pins yet. The penta pins and they just drop off. I’ll get back to playing with it later this year I hope. It does shoot well...
    38 replies | 695 view(s)
  • barrabruce's Avatar
    08-02-2021, 01:15 PM
    I’ve loaded the 308 hunter in the 30-30 with 12" twist. Shoots @ 1" at 50 yards with 4-5 grns bullseye. I also sized it to 0.302" and paper patched it and was getting @1 3/4" - 2" groups at 100 yards with jacket loads. The nose is a little small...
    38 replies | 695 view(s)
  • barrabruce's Avatar
    08-01-2021, 03:34 PM
    Oops:oops: I have the 308 hunter mould which looks similar to the one you are asking about. But it will most likely rain bullets for you as well.
    38 replies | 695 view(s)
  • barrabruce's Avatar
    08-01-2021, 10:08 AM
    You can always drill out the primer pockets in some rimless cases which is supposed to stop excess headspace in mouse fart loads. But you wouldn’t want to mix them up with full house load brass. I don’t powder coat but I believe plain base cast...
    38 replies | 695 view(s)
  • barrabruce's Avatar
    08-01-2021, 09:31 AM
    I have that mould and when you get into the rhythm they just fall out of the mould easily. Work O.k in my gun but the nose is a little small. Well I should say my bore is a little big for the mould but easily gets 1" groups at 50 yards. Keeping it...
    38 replies | 695 view(s)
  • barrabruce's Avatar
    08-01-2021, 08:30 AM
    I got a couple that I cut up wth a cold chisel into smaller lumps to make ingots out of. I’ll see if I have anything worth taking a picture of tomorrow. Definitely thumb nail soft. I wish I could source some more. These were out of a boats...
    4 replies | 451 view(s)
  • barrabruce's Avatar
    07-16-2021, 06:43 PM
    barrabruce replied to a thread Iver Johnson in Rimfire Area
    Just makes them more efficient. Interesting design thou. I donít collect them but I am drawn to the simplicity of a single shot rifle.
    10 replies | 473 view(s)
  • barrabruce's Avatar
    07-16-2021, 11:05 AM
    Yeah I can see where the barrel has been rubbed or work hardened and a fine hard finish / polish has been achieved. Yes I believe you’s are right about needing some teeth in the metal. The first couple of test ones were just a machine finish and...
    51 replies | 3314 view(s)
  • barrabruce's Avatar
    07-15-2021, 11:16 AM
    All true it is Naphtha ,white gas. It is actually petrol but in the 1940’s sense. Pure that is. It don’t go off and leaves very little waxy easters behind. They use special decantered and filtered stuff in the Antarctic as a failure is more life...
    38 replies | 1028 view(s)
  • barrabruce's Avatar
    07-13-2021, 02:22 PM
    It took 4 passes but I think my 2 cup backpacking kettle wasn’t up to snuff and left water marks as I was told would happen. Some places really didn’t take on the first pass. And never caught up. I did soak it in a pvc tube of boiling water a...
    51 replies | 3314 view(s)
  • barrabruce's Avatar
    07-13-2021, 03:09 AM
    Well I blued me Brno 1 barrel and happy with the way it came out. Learnt how I went wrong I think know.:D At one stage it was all gold like oil on a pond and I should have left it so I had a golden gun but I didn’t. Might call myself blotchy...
    51 replies | 3314 view(s)
  • barrabruce's Avatar
    07-09-2021, 11:52 PM
    This is what it looks like. Inside it’s a very dark colour but in hard light it looks transparent like looking through layers of polished wood. I think I’ll leave it as it will stop the rusting. Next time I’m going to follow the path layer out...
    51 replies | 3314 view(s)
  • barrabruce's Avatar
    07-09-2021, 01:09 AM
    Well I got my ammonium chlorite and mixed a small batch up with it. I couldn’t get it to take till I scratched the surface with the mix in steel wool. It would just bead up. I may have to return to oil removal properly. But the small section I...
    51 replies | 3314 view(s)
No More Results
About barrabruce

Basic Information

About barrabruce
Biography:
Still alive and plodding
Location:
Far Nth Qld Australia
Interests:
Classic Camp Stoves, Fishing and the odd angry shot

Statistics


Total Posts
Total Posts
1,675
Posts Per Day
0.37
Albums
Total Albums
1
Total Photos
0
General Information
Last Activity
Today 11:27 PM
Join Date
02-09-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check