RotoMetals2Lee PrecisionTitan ReloadingReloading UK
MidSouth Shooters SupplyRepackboxADvertise hereInline Fabrication

  • sixgunner452's Avatar
    06-16-2021, 01:14 PM
    Sir. Could be. But Ruger sent new replacement parts. Same problem. Think hole in slide that holds extractor out if spec. Thanks Randy.
    18 replies | 548 view(s)
  • sixgunner452's Avatar
    06-15-2021, 02:25 PM
    725, I agree. Glad I went that way. I am happy to report 8 days, almost to the hour after I called Ruger Service dept.... I received my LCP back in my hands. They replaced the complete slide assy, and the barrel. They even included a complimentary...
    18 replies | 548 view(s)
  • sixgunner452's Avatar
    06-13-2021, 11:51 PM
    Sir, I have used the Black Max t affix a front sight to a rifle barrel. Works Great. Randy.
    27 replies | 619 view(s)
  • sixgunner452's Avatar
    06-07-2021, 05:07 PM
    Gentlemen. I took ur advice. I called Ruger. They emailed a Fedex label. I mailed it off. Requested new slide assy, and barrel. Fingers crossed, hoping for best. Thanks, Randy.
    18 replies | 548 view(s)
  • sixgunner452's Avatar
    06-05-2021, 08:37 PM
    Gentlemen, I am convinced. I will give Ruger a call. Thanks, Randy.
    18 replies | 548 view(s)
  • sixgunner452's Avatar
    06-05-2021, 07:38 PM
    Loads are no where near max. 105 swc and 2.3 to 2.9 Reddot. Same as above with 95 gr FP. The same loads were tried with Vectan AS too.Thanks Randy
    18 replies | 548 view(s)
  • sixgunner452's Avatar
    06-05-2021, 06:29 PM
    Thanks to all who replied. As much as I hate to do it, I might just send it back. Thanks, Randy.
    18 replies | 548 view(s)
  • sixgunner452's Avatar
    06-05-2021, 12:32 PM
    Gentlemen, I agree with all the above. I believe in the end Ruger will make it right. I really would like to fix it myself. I was hoping for some answers on how to repair. Many thanks, Randy.
    18 replies | 548 view(s)
  • sixgunner452's Avatar
    06-04-2021, 11:35 PM
    Gentlemen, about a month back I buy a Ruger LCP 1. I take it to the range. After 4-5 rounds it fails to eject. I looked at the pistol, notice the ejector, plunger and spring are missing. I called Ruger, they sent me new parts. A couple of weeks...
    18 replies | 548 view(s)
  • sixgunner452's Avatar
    06-04-2021, 02:47 PM
    Yes, I watched a couple Utube vids explaining how to install the ejector. Randy.
    10 replies | 438 view(s)
  • sixgunner452's Avatar
    06-04-2021, 02:44 PM
    Fellers, I thought my LCP journey was over. I guess it's just started. After my last (successful) outing firing about 100 different 380/Reddot loads, I thought I would try some Vectan AS 380 loads. I was about round 97, almost finished. I looked...
    10 replies | 438 view(s)
  • sixgunner452's Avatar
    05-23-2021, 09:40 PM
    I agree with all above. 100% on the 2 cycle oil. I would also add allen screws to the sprue pivot bolts. If not your mold will self destruct pre maturely. There are tutorials in the faq section. I do not use a hot plate. Not saying its wrong. I dip...
    13 replies | 478 view(s)
  • sixgunner452's Avatar
    05-21-2021, 11:11 PM
    Sir, I will keep cfe pistol in mind, next time I see powder for sale that is. Thanks, Randy.
    10 replies | 438 view(s)
  • sixgunner452's Avatar
    05-21-2021, 09:43 PM
    Poygan, my LCP is a Gen II. I hear an improvement in trigger pull. Have no experience with a Gen I LCP. So far so good. Seems to like cast just fine. The trigger pull to me is very Glock-like. So far manageble. I just need to figure where to aim....
    10 replies | 438 view(s)
  • sixgunner452's Avatar
    05-21-2021, 07:23 PM
    My LCP being new (made in NC) I thought I may have a few probs (chatter on the web). Well other than my break-away ejector (believe its fixed now; fired a hundred 2day), it is finely finished inside and out. I hand polished a couple spots, didn't...
    10 replies | 438 view(s)
  • sixgunner452's Avatar
    05-21-2021, 07:08 PM
    WebMonkey, I have been unable to find a LFC 380 die. Sold out. Tried my 9MM FCD didn't do a thing. Most of my rounds easily chamber. All of the Lee 95 FN pass the plunk test. A few with thicker cases with the 105 SWC failed to plunk (probably...
    10 replies | 438 view(s)
  • sixgunner452's Avatar
    05-21-2021, 04:56 PM
    Gentlemen, I doubt anything I say here will be new, but here goes. Been wanting to try an LCP. I've owned a couple Keltek's. So I order one, go to pick up my Ruger LCP I from my FFL. I got the stainless slide model, I have seen a lot of rusted blued...
    10 replies | 438 view(s)
No More Results
About sixgunner452

Basic Information

Date of Birth
June 3, 1966 (55)
About sixgunner452
Biography:
Retired US Army 63B
Location:
EL PASO, TX
Interests:
Shooting, Hunting
Occupation:
Retired ELECTRONICS TECHNICIAN

Statistics


Total Posts
Total Posts
220
Posts Per Day
0.04
General Information
Last Activity
Today 01:26 PM
Join Date
08-26-2005
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check