ADvertise hereLee PrecisionTitan ReloadingReloading UK
RepackboxRotoMetals2MidSouth Shooters SupplyInline Fabrication

Tab Content
  • wv109323's Avatar
    06-12-2021, 11:21 PM
    I think any of the major brands will work. 1.) get a carbide sizing die 2.) Make sure the neck expander opens the case mouth enough so that you do not size down your bullet when seating. 3.) use a taper crimp die
    34 replies | 559 view(s)
  • wv109323's Avatar
    06-12-2021, 04:34 PM
    wv109323 replied to a thread snake boots in Our Town
    With the timber rattlers we have in WV, I would not want to test the theory that cowboy boots would stop a bite. Rattlers are not that hard to spot or hear unless you practically step on them. But the copperhead is tough to see on the forest floor....
    24 replies | 515 view(s)
  • wv109323's Avatar
    06-11-2021, 02:14 PM
    I have a plastic shotgun choke tube container. It has three compartments in it. It is about 4" x3" x11/4".
    28 replies | 819 view(s)
  • wv109323's Avatar
    06-11-2021, 02:04 PM
    Woodworker supply stores have dowel rods of walnut. Or there is a special tool that cuts plugs from boards. That way you get cross grain instead of end grain. Drill out the hole to dowel rod/plug size. Glue dowel rod in place. Sand and refinish. A...
    10 replies | 270 view(s)
  • wv109323's Avatar
    06-11-2021, 01:31 PM
    wv109323 replied to a thread Scam call in Our Town
    I just won 5.5 million dollars.
    56 replies | 3208 view(s)
  • wv109323's Avatar
    06-11-2021, 01:27 PM
    She should be able to draw on his SS if she is 62. His retirement is dependent upon the options he took out with it. Survivors benefits allows her entitlement to his retirement if he chose that option. Life insurance through his place of employment...
    20 replies | 592 view(s)
  • wv109323's Avatar
    06-06-2021, 09:47 PM
    Get some inexpensive Bibles and advertise free Bibles as gifts. Put up a notice of your church services. If anyone objects ask for the board to be taken down.
    17 replies | 314 view(s)
  • wv109323's Avatar
    06-04-2021, 11:10 PM
    The 70 series Gold Cup is not Bullseye accurate. To get top performance a match barrel will need to be installed, slide to frame tighten and the trigger may be acceptable. 70 series Colts had bar stock parts if that turns your crank. The hand fit...
    29 replies | 862 view(s)
  • wv109323's Avatar
    05-30-2021, 04:50 PM
    Most reloading manuals ( other then those put out by powder companies) will list the best powders for a caliber. Lyman even notes the most consistent load they found. There are so many powders that many powders are suitable for an application. It...
    49 replies | 5554 view(s)
  • wv109323's Avatar
    05-30-2021, 03:17 PM
    The type of firearm or testing fixture could make a difference. Bore diameter,barrel length,temperature chrono accuracy and bullet coating can all enter into the final velocity. I would do more research and maybe call the powder manufacturer.
    38 replies | 1035 view(s)
  • wv109323's Avatar
    05-30-2021, 03:03 PM
    wv109323 replied to a thread Any news????? in Our Town
    Do the people that call you asking for contributions actually work for the NRA? I thought they would be paid robo callers working from a call center and just contract workers. What is a way to express your opinion to the BoD or directly to WLP?
    20 replies | 853 view(s)
  • wv109323's Avatar
    05-27-2021, 11:37 PM
    wv109323 replied to a thread Any news????? in Our Town
    If NRA refiles the bankruptcy case, the judge has threaten a trustee to take over. The judge was not impressed with the first argument presented by the NRA for bankruptcy. Wayne will probably have to go back to NY and fight the legal battle there...
    20 replies | 853 view(s)
  • wv109323's Avatar
    05-26-2021, 10:00 PM
    wv109323 replied to a thread Bl-c(2) in Factory & Surplus Powder
    Make sure that is BL-C(2). There was a BL-C. I can't make out the photo for sure. This powder is close to Varget and WW 748. Many uses.
    22 replies | 1494 view(s)
  • wv109323's Avatar
    05-26-2021, 09:50 PM
    +1 on the dental pick(s). You can remove a lot of the material from the outside and then push it out from the inside.
    22 replies | 1689 view(s)
  • wv109323's Avatar
    05-26-2021, 09:35 PM
    wv109323 replied to a thread 1911 trouble feeding in Cast Boolits
    I don' understand the numbers .265 and .120. The 230 g. RN bulet should be 1.250 oal. Take the barrel out of the gun and use the chamber as a gauge. Use a magic marker and coat the round. Putting it back in the chamber should tell you where the...
    82 replies | 2594 view(s)
  • wv109323's Avatar
    05-25-2021, 04:14 PM
    Not much ballistic difference between the two just the physical size difference.
    17 replies | 631 view(s)
  • wv109323's Avatar
    05-22-2021, 01:28 PM
    The 1911 recoil spring and I ASSUME others no not follow mechanical engineering guidelines. The 1911 recoil spring is labeled as to the poundage that it takes to compress the spring to the minimal length in the firearm under recoil. This dimension...
    20 replies | 670 view(s)
No More Results
About wv109323

Basic Information

About wv109323
Biography:
Age 60
Location:
Lenore, WV
Interests:
Cars Guns Photography
Occupation:
Disabled

Statistics


Total Posts
Total Posts
2,548
Posts Per Day
0.56
General Information
Last Activity
06-15-2021 07:56 PM
Join Date
01-02-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check