Lee PrecisionReloading UKInline FabricationTitan Reloading
ADvertise hereRotoMetals2MidSouth Shooters SupplyRepackbox

Tab Content
  • wv109323's Avatar
    09-07-2021, 08:57 PM
    I had a 127 that was made in 1970-72. It was a tank and going strong when I sold it because I sold the rural property I had. I did minimal work to it. Belts, oil changes and deck bearings.
    4 replies | 276 view(s)
  • wv109323's Avatar
    09-06-2021, 12:13 PM
    It seems a lot of models are out of stock. They introduced a new model but I have not seen it in stock anrwhere. I don't own one but most all people are satisfied.
    15 replies | 376 view(s)
  • wv109323's Avatar
    09-06-2021, 11:43 AM
    I smell a scam. Zelle is a quick method to send money from your bank account. A legit business should have multiple ways to receive payment. They should not be telling you how you should pay. I would run.
    9 replies | 404 view(s)
  • wv109323's Avatar
    09-04-2021, 09:05 PM
    I found that seating the bullet that large made some rounds that would not chamber. Setting the bullet so it was straight on the case before seating is critical. If there was a slight bulge it can cause the round not to chamber. I was using Lee dies.
    16 replies | 464 view(s)
  • wv109323's Avatar
    09-04-2021, 08:54 PM
    The barrel is throated to accept larger longer rounds. Groups fired after the BE groups were normal and did not tumble so I can not assume barrel was leaded. All boolits were coated so less likely to lead barrel.
    13 replies | 318 view(s)
  • wv109323's Avatar
    09-04-2021, 08:50 PM
    Misprint in previous post. PF is suppose to be 130 not 230.
    13 replies | 318 view(s)
  • wv109323's Avatar
    09-04-2021, 08:48 PM
    The boolits are not being sized down when seated. I have a special powder funnel that neck sizes for cast. Pulled boolits are still as sized .3570 and .3582. I shot some groups with 5 rounds of same headstamp(BHA) and 5 rounds misc. brass. This...
    13 replies | 318 view(s)
  • wv109323's Avatar
    09-04-2021, 11:45 AM
    I am in pursuit of a load for USPSA in a CZ 75B Omega. The bore slugs to .3562 and is a 1:10 twist. The pistol was shot in a Ransom Rest at 20 yards. Everything is the same except the bullet size in the two loads. The brass was miscellaneous. The...
    13 replies | 318 view(s)
  • wv109323's Avatar
    09-04-2021, 11:13 AM
    wv109323 replied to a thread Shopsmith mark v in Our Town
    My uncle had one and used it for years. He built two houses and made the kitchen cabinets with the Shopsmith. The jig saw was not up to his standards but the rest he used for 30 years. No doubt individual tools are better and more flexible because...
    35 replies | 759 view(s)
  • wv109323's Avatar
    08-30-2021, 01:44 PM
    I shake and bake my PC bullets with Smokes powder. I use black BB's in a smaller container. My boolits are acceptable but the coating is an uneven coat. I would like to get a thicker more even coat. What are the secrets to getting a thicker more...
    19 replies | 540 view(s)
  • wv109323's Avatar
    08-29-2021, 08:36 PM
    My bench top overhangs the frame of my bench. I use a 2 lb. lard can hung on a nail. Trouble is lard don't come in a can anymore. Old school Redneck engineering.
    18 replies | 673 view(s)
  • wv109323's Avatar
    08-29-2021, 08:30 PM
    One thing with the 550 you may want to consider. Your rifle brass will need to be trimmed at some point. There is no way to do that on the 550. I de-prime, resize and trim brass before I start to load rifle on a 550. You also mentioned cleaning your...
    45 replies | 1300 view(s)
  • wv109323's Avatar
    08-29-2021, 08:11 PM
    wv109323 replied to a thread New To Casting in Cast Boolits
    Your mold choice may depend on how you size/lube or powder coat your boolits. Your mentioned choices are fine. There are several quality mold makers:RCBS, Saeco, NOE, Accurate molds and Mi-hec. These are all top quality. Availability is uncertain...
    7 replies | 199 view(s)
  • wv109323's Avatar
    08-25-2021, 04:16 PM
    For extra torque use a pair of Vise-grips on the shank of the screwdriver(if the shank is round). If the shank is square use an adjustable wrench. You may need someone to hold the screwdriver in the screwhead to keep from stripping it. I use...
    62 replies | 1642 view(s)
  • wv109323's Avatar
    08-22-2021, 09:28 PM
    I have the cheap one from Wal-mart. The wires going to coil have burnt or come loose several times. Easy fix but kinda bad during a casting session.
    34 replies | 1016 view(s)
No More Results
About wv109323

Basic Information

About wv109323
Biography:
Age 60
Location:
Lenore, WV
Interests:
Cars Guns Photography
Occupation:
Disabled

Statistics


Total Posts
Total Posts
2,598
Posts Per Day
0.56
General Information
Last Activity
09-18-2021 09:52 PM
Join Date
01-02-2009
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check