Lee PrecisionWidenersRotoMetals2Titan Reloading
MidSouth Shooters Supply

Tab Content
  • Rapier's Avatar
    Yesterday, 12:57 PM
    Before you start, gather up your equipment, mark your property line corners and lay out the fence to scale. An entrance gate off a 2 lane street 90 degree turn takes 24 feet for a fire truck or a truss truck. That is a double 12' leaf gate. Cars and...
    24 replies | 419 view(s)
  • Rapier's Avatar
    11-30-2022, 02:44 PM
    Problem is they have the same old twist rate for the 110 grain round nose bullets. The Contenders in 30 Carbine have a 1-10 twist and will shoot heavier bullets with good accuracy. However, it head spaces on the case mouth and grows in length with...
    11 replies | 364 view(s)
  • Rapier's Avatar
    11-30-2022, 01:36 PM
    Interesting post, I have a few presses, started with a Lyman Tong Tool, still have one for my go bag, with a set of dies, dipper, a Lyman 38 cal 158 SWC plain base mould and lube cutter made from a cut off 38-55 case wrapped with speed tape....
    63 replies | 2005 view(s)
  • Rapier's Avatar
    11-29-2022, 03:59 PM
    The Cadet chamber/ bolt make up a curve that a case with bullet must make to chamber. The 357 Super Mag works with spire point or round nose rifle bullets, the problem comes with pistol bullets and the blunt nose,, like the SWC. I have two 357 SM...
    10 replies | 296 view(s)
  • Rapier's Avatar
    11-29-2022, 03:31 PM
    Rapier replied to a thread Gunsmith in Military Rifles
    Might ask a member of the OGCA see if they can give you a guiding light on that. Their shows are members only shows or used to be and they have some very good smiths as members.
    3 replies | 316 view(s)
  • Rapier's Avatar
    11-29-2022, 02:39 PM
    Rapier replied to a thread My son disowned me in Our Town
    Do not have any family stories, mine are angels [smilie=s:. Of course I am reminded now and then of "You can pick your friends but not your family." Young men are a trial at times especially when trying to get grown. Old, young men that never...
    63 replies | 2382 view(s)
  • Rapier's Avatar
    11-29-2022, 02:02 PM
    The "original" 300 BO was the 300 Whisper, Bill at AAC did not like paying JD for the rights so created a slight change in the deminsions, called it the 300 BO and sold them with a marketing program that made the cartridge sound like a 300 Win Mag,...
    25 replies | 786 view(s)
  • Rapier's Avatar
    11-27-2022, 05:16 PM
    If the unlocking piece (dum bell looking piece) is bent the action will not unlock. Push the lugs in with your thumb and push the keeper pin, in the barrel block, out, the lugs, spring and unlocking piece will come out. If that unlocking piece is...
    8 replies | 413 view(s)
  • Rapier's Avatar
    11-27-2022, 11:55 AM
    I run the hard cast 200 grain RCBS flat nose plain base in my 35s. I PC shake and bake the bullets using a hardware cloth box, bullets baked nose down, then sized to the actual groove diameter. I have a 12, 14, 16 and a 20 twist, rifles, they all...
    10 replies | 554 view(s)
  • Rapier's Avatar
    11-26-2022, 07:49 PM
    If you need to turn the ejector rod use the paddd vice to hold the rod and turn the cylinder with your hand, unscrewing the rod. Just turn it in the correct direction and do not bend the rod.
    9 replies | 236 view(s)
  • Rapier's Avatar
    11-26-2022, 07:31 PM
    Today you just about need to call, to make sure people are still working. I get asked all of the time, my stock answer is call first.
    11 replies | 670 view(s)
  • Rapier's Avatar
    11-26-2022, 01:24 PM
    I would run my alloy 100# pot up to a high temperature so the unknowns have a better chance to mix, plus allow the sand to go to the bottom as you stir. You really have no idea what folks have used to make their bullets. I prefer a commercial powder...
    18 replies | 622 view(s)
  • Rapier's Avatar
    11-25-2022, 11:37 AM
    Yes, Eben (E Author Brown) does good work on single shots, He own BF as well as does Contenders and Encore guns stuff. were it Me, and I had a 357 Mag single shot barrel, I would just ream the chamber to a 357 Super Mag (max). It is roughly 1/4"...
    20 replies | 527 view(s)
  • Rapier's Avatar
    11-25-2022, 11:26 AM
    Probably .12 to .13 would be close for a flat point 45 cal. Larry Medler's Silhouette Ballistics program will run actual scope adjustments in clicks and incremental trajectory tables which you can print and put on a scope front bell with clear...
    11 replies | 352 view(s)
  • Rapier's Avatar
    11-25-2022, 11:13 AM
    I PC, then size to the exact groove diameter, using case lube. I have found that it is important for the bullets to slide in the die. For my ARs I use a hard alloy, shake and bake, using a hardware cloth box, plain base bullets set nose down, no GC....
    12 replies | 410 view(s)
  • Rapier's Avatar
    11-25-2022, 11:06 AM
    A true classic TV episode.
    21 replies | 706 view(s)
  • Rapier's Avatar
    11-24-2022, 01:49 PM
    Do not forget the TC carbines, Encore and Contenders. Perfect for a straight wall case. Plus the 357 Super Mag (Max) You can buy a 357 Mag single shot and run a reamer into it to change it to a SM. They shoot cast well with a 12 or 14 or 16 twist...
    49 replies | 1692 view(s)
  • Rapier's Avatar
    11-24-2022, 08:08 AM
    First thing, check you speed of sound at your location and load the PC 230 grain bullets below that number. I use the JD Jones data on the 300 Whisper with H-110 and 296. About 1,000fps that shoots sub 1/2" at 50 in my 1-8 twist 16"AR. Alloy is very...
    7 replies | 281 view(s)
  • Rapier's Avatar
    11-23-2022, 01:17 PM
    If you buy the proper bases and put them on correctly, with the right screws in each base, they will go on correctly. Get the screws backwards and you will have bolt function problems. If you want to use locklight, use only blue do not use red....
    20 replies | 610 view(s)
  • Rapier's Avatar
    11-23-2022, 12:48 PM
    I saw Bill Rogers casting operation working with Magma machines. He was running 38 Spl remanufactured ammo at the time with SWC cast bullets. Casting in one building and reloading in another building. Those casting machines are something to watch.
    15 replies | 453 view(s)
  • Rapier's Avatar
    11-23-2022, 12:20 PM
    Very good 358 performance. Nice WT buck with an excellent woods cartridge.
    25 replies | 672 view(s)
  • Rapier's Avatar
    11-22-2022, 07:20 PM
    What Blahut said. Inconsistent function, means crud, normally.
    4 replies | 254 view(s)
  • Rapier's Avatar
    11-22-2022, 07:14 PM
    Seems like you would be mile ahead of the game to find a cobby XYZ gun that you like and have it re-barreled with exactly what you want, cut rifling, for cast, twist for your preferred weight bullets and chambered in 38-55. Before you buy what you...
    17 replies | 670 view(s)
  • Rapier's Avatar
    11-22-2022, 06:35 PM
    Taper crimp as a separate station on the Dillon. Seat no crimp at all, then taper crimp, with no seater plug.
    15 replies | 505 view(s)
  • Rapier's Avatar
    11-22-2022, 09:30 AM
    Rapier replied to a thread Why I Take My Lab in Hunting with CB's
    Yes, good dog..... Had the Mitchell, SD experience in November, after they had done the combining, needed a greyhound racing dog to run down the pheasants. At least you had a nice day with your hunting buddy.
    9 replies | 507 view(s)
  • Rapier's Avatar
    11-21-2022, 02:31 PM
    Decided to build a PSA Dagger, a modified clone of the Glock 19 gen 3. So did a few advances on the gen 3, trigger, sights, etc. Need to run a throating reamer in the SAMMI chamber to taper the lands a bit. Loaded some 115 ASP J bullet rounds with...
    11144 replies | 1696510 view(s)
  • Rapier's Avatar
    11-21-2022, 02:16 PM
    Sad failure in the learning process about what a gun is for and how it must function to do its job. Keeping the gun clean is basic to it being able to perform its job in life. It ain't a tomato stake. Every day I get another non-maintained gun in...
    44 replies | 1305 view(s)
  • Rapier's Avatar
    11-21-2022, 12:33 PM
    There is no way to hang a sizable picture without a hole some place. What I did was make a 3/16" drill hole at the top of the brick in the mortar joint so that you can not see the hole when standing on the floor, then drove a 12# common nail into a...
    20 replies | 542 view(s)
  • Rapier's Avatar
    11-19-2022, 05:39 PM
    Rapier replied to a thread Best Movie Remakes in Our Town
    Today, were it not for great previous movies and comic books there would be no 2022 Jollywood. Incredibly incompetent is a better title for an award.
    41 replies | 1277 view(s)
  • Rapier's Avatar
    11-18-2022, 06:02 PM
    Rapier replied to a thread Darr Roller in Single Shot Guns
    Suggest you search the forums for the 2013 thread on the 35-40 M.
    33 replies | 1741 view(s)
More Activity
About Rapier

Basic Information

About Rapier
Biography:
Shot cast only in silhouette competition from 82-09.
Location:
NW Florida
Interests:
Shooting, casting, repairing and building firearms
Occupation:
Tree Farmer/retired executive

Signature


“There is a remedy for all things, save death.“
Cervantes

“Never give up, never quit.”
Robert Rogers
Roger’s Rangers

There are three kinds of men. The one that learns by reading. The few who learn by observation. The rest of them have to pee on the electric fence for themselves.
Will Rogers

Statistics


Total Posts
Total Posts
603
Posts Per Day
0.76
General Information
Last Activity
Yesterday 12:57 PM
Join Date
09-27-2020
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check