Lee PrecisionTitan ReloadingADvertise hereInline Fabrication
MidSouth Shooters SupplyRotoMetals2Repackbox

Tab Content
  • 15meter's Avatar
    06-26-2022, 07:03 PM
    Doubt it, that's a whole bunch of brass that has to go "somewhere". Just swaging out military primer pocket crimps on occasion can take more mechanical effort than you'd think.
    11 replies | 324 view(s)
  • 15meter's Avatar
    06-26-2022, 06:42 PM
    Could be 11mm, my Model 82 Gov't Kimber 22 target rifle has 11mm grooves. The peep sight set that came with the rifle won't work on my Model 52. When I scoped the Kimber, I had to track down metric air rifle mounts. Just a guess, worth every...
    7 replies | 257 view(s)
  • 15meter's Avatar
    06-25-2022, 11:34 PM
    Just did a little digging, there is a 13/64" endmill available from McMaster-Carr. 13/64 is equal to 0.203125, Large rifle primers are .128 inches in height and .212 inches in width. Start with the 13/64 endmill and finish with the primer...
    11 replies | 324 view(s)
  • 15meter's Avatar
    06-25-2022, 11:23 PM
    Well, you got me curious, so I went out to the shed, chucked up a 450 Bushmaster in the South Bend with a collet in the headstock. I've got a Sinclair carbide primer pocket uniformer. That went into the chuck in the tailstock. Basically used it...
    11 replies | 324 view(s)
  • 15meter's Avatar
    06-25-2022, 12:37 PM
    Guess I have to ask the question. Why? 450 Bushmaster is fairly common around here. Also seems to pop up in the S&S fairly regularly. Do you see an advantage to using 284 brass? Or is this just wanting to see if it is possible? I've gone...
    3 replies | 100 view(s)
  • 15meter's Avatar
    06-25-2022, 12:45 AM
    Best use of a chronograph was a tumble test 25+ years ago, a couple of guys were on the range with a chronograph they had borrowed from a buddy. These guys were HARD core trap shooters. Their definition of an accurate rifle was hitting an 8"...
    56 replies | 719 view(s)
  • 15meter's Avatar
    06-24-2022, 11:44 PM
    Never have tried to move from small to large primer, it will be interesting to see if someone chimes in who has done it. I'm surprised no one else has asked this question with current weirdness in components. I'm fooling with the best...
    11 replies | 324 view(s)
  • 15meter's Avatar
    06-22-2022, 10:50 PM
    I've formed a fair number of cases over the years, upfront I have never done this one. So this is pure guess work. On other cases, I've had better luck when pushing a shoulder lower on a case is to straighten the case out closer to a straight...
    6 replies | 230 view(s)
  • 15meter's Avatar
    06-21-2022, 10:58 PM
    I have never fire formed 30-30 AI but I have taken 30-30 out to 38-55. I believe I used 10 grains of Unique, 1/4 sheet of toilet paper over the powder, filled the case up with the screenings from under a buddies grain dryer(did I mention I'm...
    6 replies | 277 view(s)
  • 15meter's Avatar
    06-21-2022, 10:28 PM
    Biggest improvement for me would be a better internal search engine. It changed a while back and I don't believe it works as well as when I started 5 years ago. A lot of my searches are done from outside the forum but specifying cast boolits in...
    67 replies | 1669 view(s)
  • 15meter's Avatar
    06-20-2022, 08:08 AM
    Whack-a-Mole dies are popular with the survivalist types. Depending on the caliber can go for, at times, silly amounts of money.
    22 replies | 840 view(s)
  • 15meter's Avatar
    06-19-2022, 10:55 PM
    Look up Lyman M-die. It's designed to do exactly what you need. RCBS I believe has a similar die. Lee makes a generic expander that sort of works. It just flares the very mouth of the case. Most cost effective is the Lee expander body with a...
    29 replies | 602 view(s)
  • 15meter's Avatar
    06-19-2022, 10:29 PM
    Annealing will certainly help with case life, not as much as you would like, most of my hornet case lose has been from burn through about half way up the neck as opposed to brittle neck splitting. Next cause of case lost is case head separation....
    12 replies | 482 view(s)
  • 15meter's Avatar
    06-19-2022, 09:52 PM
    Like it right where I am. Last Sunday, skeet league in the AM, visit a long time friend in the early afternoon then drove up north to a buddy's place for Sunday evening. Beers and bonfire. Monday went to a big bowling pin shoot @ Central Lake...
    65 replies | 2197 view(s)
  • 15meter's Avatar
    06-19-2022, 09:08 PM
    Shot trap today with 700X from a black steel can. It's been a year or two since it was in steel cans. Shot skeet and sporting clays last summer with Winchester primers that were in boxes with machined wood dividers. Every one went BANG! Shot...
    22 replies | 840 view(s)
  • 15meter's Avatar
    06-19-2022, 08:47 PM
    Is it bad powder or a bad can? I had a can of powder I thought had gone bad, was about to throw it out and decided a closer look was in order. Dumped it into a different can and looked at the original can very closely, the inside of the can was...
    17 replies | 570 view(s)
  • 15meter's Avatar
    06-18-2022, 08:18 PM
    If an airgun will whack an iguana at distance, I think a bb gun would probably be adequate for Chip and Dale up close and personal. https://m.youtube.com/watch?v=Wv6t3NZyy2Q
    61 replies | 1887 view(s)
  • 15meter's Avatar
    06-18-2022, 07:14 PM
    I've melted a bunch of range scrap with wood. I took a propane tank that was bigger than the standard 20 pound, don't remember what size it was. Cut the bottom off, flipped the top over and welded 3 legs on it. Threaded the valve out and...
    8 replies | 401 view(s)
  • 15meter's Avatar
    06-17-2022, 10:36 PM
    May not have to be specific Texan shellholders. I have a number of 60's-70's vintage RCBS shell holders that have the larger through hole. Post what you have and what you are looking for in S&S, you may get a trade that will work for you. ...
    6 replies | 1575 view(s)
  • 15meter's Avatar
    06-17-2022, 10:10 PM
    It's surprising the uneven distribution of components across the country. Here in Michigan, powder started filtering back into the gun shops last fall. There were a couple that never ran out completely. Currently all the shops have a pretty...
    2118 replies | 554870 view(s)
  • 15meter's Avatar
    06-17-2022, 01:05 PM
    By the cup? Well I guess we do use recipes in loading:kidding:
    2118 replies | 554870 view(s)
  • 15meter's Avatar
    06-16-2022, 09:06 AM
    This! Knew a crazy old dude who went to war on ground moles with a 450 Nitro Express and other such implements of mass destruction. He would sit in a lawn chair in the front yard, when the dirt moved he shot. Claimed you didn't have to hit...
    61 replies | 1887 view(s)
  • 15meter's Avatar
    06-16-2022, 08:41 AM
    https://castboolits.gunloads.com/showthread.php?443113-500-450-No-1-BPE Check post #14, I'm just starting playing with 209 primers in Berdan cases. It may be a solution to your problem. Other people have done it successfully, for light loads...
    8 replies | 395 view(s)
  • 15meter's Avatar
    06-15-2022, 10:48 PM
    If I still had a memory I could list the specific upgrades I did to my Mark II. I remember: Extended bolt latch lever Extended magazine release Firing pin
    16 replies | 609 view(s)
More Activity
About 15meter

Basic Information

About 15meter
SE Michigan


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 01:51 PM
Join Date

1 Friend

  1. jorgeb2016 jorgeb2016 is offline

    Boolit Mold

Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check