Inline FabricationLee PrecisionRepackboxWideners
MidSouth Shooters Supply

Tab Content
  • Jevyod's Avatar
    01-22-2023, 08:49 AM
    I used the Lee 35-200 cast out of. 94-3-3 alloy (weighed 204 grains with gas checks) Velocity was 1900 fps out of my 358 win. Used it to take 2 deer this year, they worked very well. Because they worked that well I am currently working up a load for...
    15 replies | 472 view(s)
  • Jevyod's Avatar
    01-05-2023, 02:25 PM
    I have a 358 Win built on a Mauser 98 action. The 2 cast bullets I shot were the RCBS 35-200, and the NOE 360-232. That one has a wide meplat of .275 inches. I had to seat it a little bit deeper so the edge didn't catch, but it worked and fed fine....
    15 replies | 767 view(s)
  • Jevyod's Avatar
    01-04-2023, 10:30 AM
    Ok I looked again, yours is showing 5% antimony which is way high. Pewter has about that, but when adding 16lbs pure, no way should it be 5%!
    30 replies | 854 view(s)
  • Jevyod's Avatar
    01-04-2023, 10:28 AM
    fascinating, mine shows 10.5??!!! I can't quite tell, what does the bottom composition show on your chart?? Mine shows 5.44% tin, 0.35% antimony, 0% arsenic, .09% copper, 0% silver, and 94.1% lead for a hardness of 10.5!
    30 replies | 854 view(s)
  • Jevyod's Avatar
    01-02-2023, 03:24 PM
    I ran the numbers on the spreadsheet and according to what I was able to ascertain 16 pure to 1 pewter gave me 10.5 bhn. Not sure the 15.6 is correct!
    30 replies | 854 view(s)
  • Jevyod's Avatar
    01-02-2023, 09:28 AM
    I am working with a CVA Wolf muzzleloader, 1:28 twist, 50 Caliber. Planning on using the Lee 452-300 in sabots, in the 1600-1800 fps range
    30 replies | 854 view(s)
  • Jevyod's Avatar
    01-01-2023, 04:30 PM
    The meplat on that bullet is not that big, but with my alloy it appeared to get decent expansion
    9 replies | 644 view(s)
  • Jevyod's Avatar
    01-01-2023, 04:28 PM
    This year I used lee 35-200, a copy of the rcbs. Mine weighed about 202 grains gas checked. I used them to shoot 2 deer this year at 1900 fps (358 winchester) I know a lot say 50/50 is the ultimate, but I used coww with enough pewter added to make a...
    9 replies | 644 view(s)
  • Jevyod's Avatar
    01-01-2023, 02:32 PM
    So you all would use pure, even at 1600-1800 fps? Wouldn't that flatten too much?
    30 replies | 854 view(s)
  • Jevyod's Avatar
    12-30-2022, 08:45 PM
    I have always worked with coww or a mixture of coww/pure. I am getting into muzzleloaders, and was encouraged to use a 1:16 alloy. 2 questions, any real problem using pewter instead of tin at the same 1:16 ratio? 2nd question, at what velocity does...
    30 replies | 854 view(s)
No More Results
About Jevyod

Basic Information

Statistics


Total Posts
Total Posts
435
Posts Per Day
0.13
General Information
Last Activity
Yesterday 02:06 PM
Join Date
10-17-2013
Referrals
0

1 Friend

  1. MBTcustom MBTcustom is offline

    Boolit Grand Master

    MBTcustom
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check