RepackboxReloading UKTitan ReloadingLee Precision
Inline FabricationADvertise hereMidSouth Shooters SupplyRotoMetals2

Tab Content
  • cheese1566's Avatar
    Yesterday, 11:29 PM
    1/2” copper and cpvc line are 5/8” od… But I want clear.
    6 replies | 97 view(s)
  • cheese1566's Avatar
    06-12-2021, 01:43 PM
    6 replies | 97 view(s)
  • cheese1566's Avatar
    06-12-2021, 11:16 AM
    What’s the outside diameter of the Lee Case Feeder tubes? Hoping they are 5/8” (0.625”) to use on my RCBS green machine. Checking before I order those or bulk polycarbonate tube
    6 replies | 97 view(s)
  • cheese1566's Avatar
    06-09-2021, 10:44 PM
    I like how the 3rd gen manual clearly states one should read and read again the manual to understand the complexity of the machine, and that any previous reloading experience doesn’t matter. I am no engineer, but I have a good understanding in...
    13 replies | 347 view(s)
  • cheese1566's Avatar
    06-08-2021, 10:40 AM
    Don’t throw hate towards it! I have been intrigued by these little guys and know of all the lost patience and anger towards them. This one came up locally and picked it up near Devils Tower Wyoming. Missing the poor design primer tray, case tubes...
    13 replies | 347 view(s)
  • cheese1566's Avatar
    06-07-2021, 05:59 PM
    In need of the top and bottom of the case feeder for a RCBS Green Machine. (Case feeder index wheel) I have one but it pretty worn. Just got off the phone with RCBS Tech and they no longer have the wheels or tubes.
    0 replies | 156 view(s)
  • cheese1566's Avatar
    06-01-2021, 09:09 AM
    This one has a basic worm drive gear box and the mechanics used pulleys and steel cable. Based on the entire unit, I am pretty sure it will reverse, otherwise it would only raise or lower the chair. The motor label has no other info, and looks to...
    6 replies | 347 view(s)
  • cheese1566's Avatar
    05-31-2021, 02:31 PM
    I tried googling the numbers, but had no luck. Also, the mystery box had no info other than “this side up” on one side. Here is the label.
    6 replies | 347 view(s)
  • cheese1566's Avatar
    05-30-2021, 11:43 PM
    Need someone with experience in motor wiring to get this motor wired up. It is a 120v ac single phase that came from a handicap chair lift system. I would like to eventually get it adapted to my RF45 mill to raise the head. It also has a...
    6 replies | 347 view(s)
  • mtnman31's Avatar
    05-24-2021, 09:54 AM
    I've got a set of RCBS dies and 400 35gr JHP bullets (I think they're Hornady XTPs). $85 shipped
    5 replies | 234 view(s)
  • kungfustyle's Avatar
    05-21-2021, 04:09 PM
    Sorry for your loss.
    51 replies | 1080 view(s)
  • mtnman31's Avatar
    05-19-2021, 03:21 PM
    Another thumbs up for the Lee 401-175 TC mold. It works great in both the 40's I have used it in. No feed issues and accuracy is good. I cast for these using clip-on wheel weight alloy and size to .401", lube is White Label X-Lox 2500+.
    19 replies | 616 view(s)
No More Results
About mtnman31

Basic Information

About mtnman31
Knoxville, TN until I get back to Montana.
Guns and whatnot
Marine extraordinaire


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 08:14 PM
Join Date

2 Friends

  1. cheese1566 cheese1566 is offline

    Boolit Master

  2. kungfustyle kungfustyle is offline

    Boolit Master

Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check