WidenersMidSouth Shooters SupplyInline FabricationRepackbox

Tab Content
  • ShooterAZ's Avatar
    Yesterday, 07:09 PM
    ShooterAZ replied to a thread Do We Melt or Smelt in Cast Boolits
    This thread just got "Jockularized". Who really cares if it is melting, smelting, refining, or schmelting, as long as it results in galena being poured into a boolit mold... Right? Please Cast some awesome boolits and get on with it!
    78 replies | 1153 view(s)
  • Larry Gibson's Avatar
    Yesterday, 12:13 PM
    Larry Gibson replied to a thread 16-1 in Lead and Lead Alloys
    The use of some "fluxes" are also excellent "reductants" to remix the oxidized alloy back into the mix. Beeswax and paraffin are two. They work quite well with alloy that is already smelted. While they will flux the oxidized alloy back into the...
    20 replies | 336 view(s)
  • Larry Gibson's Avatar
    Yesterday, 11:47 AM
    Problem with a "double lung" is it works if the deer is broadside. Even then the deer can go a long way before lying down to die. If you've got good tracking conditions and no other hunters in the local (I have had two deer I double lunged go far...
    24 replies | 624 view(s)
  • Larry Gibson's Avatar
    Yesterday, 10:37 AM
    If you want maximum magnum level performance, best accuracy and velocity, especially out of the rifle then try (if you can find one) the Lyman 313631 . Perhaps Accurate or NOE can clone one? If you want a plinking bullet for modest loads the...
    9 replies | 225 view(s)
  • Larry Gibson's Avatar
    Yesterday, 10:29 AM
    Larry Gibson replied to a thread 16-1 in Lead and Lead Alloys
    None at all. Once the tin is mixed into solution with the lead it will not be separating from the lead during any kind of normal casting operation. As mentioned the "scum" that forms on top is the same alloy that is just oxidized.
    20 replies | 336 view(s)
  • Larry Gibson's Avatar
    Yesterday, 10:19 AM
    Larry Gibson replied to a thread Perfect boolit? in Cast Boolits
    Ed I knew about WQing back in the '60s or early '70s from an article in a magazine about a fellow who demonstrated MGs for sale. He was using cast bullet loads for such casting them of WWs. Was a simple way of heat treating them. I doubt...
    31 replies | 568 view(s)
  • Larry Gibson's Avatar
    Yesterday, 10:13 AM
    Larry Gibson replied to a thread Perfect boolit? in Cast Boolits
    Yes, just one mould and filling all 4 cavities. I let the alloy roil back up out of each cavity before moving to the next and I leave a very generous sprue. The mould is then set on an old M60 barrel changing glove where i watch the sprue harden. ...
    31 replies | 568 view(s)
  • Larry Gibson's Avatar
    Yesterday, 10:01 AM
    Larry Gibson replied to a thread 358 winchester in Cast Boolits
    On white tail deer the RCBS 35-200-FN of the NOE or Lee clones at 2000 - 2300 fps will kill them all day long out to 200+ yards. That is, of course, unless you hunt where PETA/APCA are issuing the deer body armor. Then you may want a bit...
    6 replies | 146 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 10:41 PM
    It's still the original military 2 stage trigger. I just fine tuned it with a trigger stop and a crisp 3 pound pull . Been a while since I've had it apart but as I recall it was basically a M98 trigger.
    10 replies | 295 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 10:31 PM
    "Ultimately I just want to shoot the rifle to the sights as they were designed for the M-2 ammo." The sights on the M1 Rifle were not designed or regulated for M2 ammunition. The sights were designed and regulated for M1 ammunition, the 174 gr...
    14 replies | 359 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 10:16 PM
    Larry Gibson replied to a thread 16-1 in Lead and Lead Alloys
    That "crud" on top of each alloy is simply oxidized alloy. When you flux it will mix right back into the alloy. The crud is the same alloy as still molten. It is not tin separating from the alloy. As mentioned, what is happening is what...
    20 replies | 336 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 10:06 PM
    Larry Gibson replied to a thread Perfect boolit? in Cast Boolits
    Because I push my 30 XCBs pretty hard at 50,000 +/- psi the extra hardness is proven to help them withstand that level of acceleration. With my match 30 XCBs, 311466s and 314299s WQing will bring the #2 alloy up to linotypes BHN without the...
    31 replies | 568 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 10:00 PM
    Larry Gibson replied to a thread Perfect boolit? in Cast Boolits
    I use a large older galvanized mop bucket filled about 2/3 with tap water. I have not found any deformation from Water Quenching. When casting my match level bullet, 30 XCB, 311466 and 314299, I just use the one mould (all are 4 cavity moulds). ...
    31 replies | 568 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 09:58 PM
    Larry Gibson replied to a thread Perfect boolit? in Cast Boolits
    No. With my match bullets I seat the GCs separately using the Lyman tool on the 450. Then I only lube the bullets in an H&I die of the same diameter as the as cast diameter. With my 30 XCBs which drop at .3105 for example, I lbne them in a...
    31 replies | 568 view(s)
  • ShooterAZ's Avatar
    01-29-2023, 05:12 PM
    My personal favorites are the RCBS 38-140-CM, or the RCBS 38-158-CM. They are both a RF design which makes them quicker to load with a speedloader, as compared to a SWC. I really do like the RCBS 38-150-SWC as well, it just doesn't load as easily....
    28 replies | 610 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 03:34 PM
    I've been forming cases using 30-06 military for the 7.65 Argentine for many years. Back when available picked up several hundred R-P 8x57s that just need sizing in 7.65 FL die and a bit of trimming. With the 8x57 and LC M72 match '06 cases I...
    39 replies | 3728 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 03:10 PM
    For many years I've found the 358156, GC'd and cast of 16-1 alloy and HP'd pushed at 1400 fps out of a 6 - 7 1/2" barreled revolver to be an excellent deer killer.
    20 replies | 445 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 09:58 AM
    "I could be wrong, but I don't think there's any other cast bullet rifle cartridge that's as sensitive to RPM threshold as the 6.5x55 Mauser." 405grain Only one that comes to mind is the 5.56 ARs with 7 and 8" twist barrels. I don't mind the...
    10 replies | 295 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 09:30 AM
    Huh? [smilie=l:
    21 replies | 366 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 09:25 AM
    I've always gone with the 5 BHN so that's probably close enough. Was just confused by the NSIS BHN and getting that same measurement with the sample of supposed pure lead I was sent.
    35 replies | 1134 view(s)
  • Larry Gibson's Avatar
    01-29-2023, 09:20 AM
    Larry Gibson replied to a thread Perfect boolit? in Cast Boolits
    Except for bullets of 300+ gr weight I cast with a bottom pour Lyman Mag20. I keep the alloy at 710 - 725 degrees when casting. I use two thermometers, one measures the bottom half and the other the top half. I adjust the casting tempo to not...
    31 replies | 568 view(s)
  • Larry Gibson's Avatar
    01-28-2023, 10:06 PM
    Larry Gibson replied to a thread Perfect boolit? in Cast Boolits
    Ten years ago, I thought I was casting pretty good bullets, excellent in fact. However. the more I got into shooting cast bullets at HV I found while I was casting good, excellent bullets I too hit the accuracy wall that is alluded to. I also...
    31 replies | 568 view(s)
  • Larry Gibson's Avatar
    01-28-2023, 12:14 PM
    Best accuracy with the 6.5x55 in Swede milsurp barrels will be in the 1200 to 1700 fps range. Acceptable accuracy can be had up through 1600 - 1900 fps. Easier to get best accuracy with the shorter 129 gr 266455 or the Kurtz 130 gr cast bullet. ...
    10 replies | 295 view(s)
  • Larry Gibson's Avatar
    01-28-2023, 12:10 PM
    Shades of the RPM Threshold......:drinks:
    10 replies | 295 view(s)
More Activity
About ShooterAZ

Basic Information

About ShooterAZ
Location:
Flagstaff, AZ

Statistics


Total Posts
Total Posts
10,749
Posts Per Day
2.66
General Information
Last Activity
Yesterday 07:20 PM
Join Date
01-09-2012
Referrals
1

5 Friends

  1. 2400 2400 is offline

    Boolit Bub

    2400
  2. Larry Gibson Larry Gibson is offline

    Boolit Grand Master

    Larry Gibson
  3. Lizard333 Lizard333 is offline

    Boolit Master

    Lizard333
  4. MOA MOA is offline

    Boolit Master

    MOA
  5. swheeler swheeler is offline

    Boolit Grand Master

    swheeler
Showing Friends 1 to 5 of 5
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check