RepackboxRotoMetals2MidSouth Shooters SupplyInline Fabrication
Titan ReloadingLee PrecisionADvertise here

Tab Content
  • popper's Avatar
    Yesterday, 04:24 PM
    Too many others already in BO. 1k$ min when a 400$ works fine. BO is decent for deer at short range. Hogs usually want a larger mag. Advantage of the Long Ranger is 'long range'. 308 or 223 or others. BO isn't a long range cartridge. They could...
    9 replies | 177 view(s)
  • popper's Avatar
    Yesterday, 10:09 AM
    Long Ranger platform would not be a viable 300BO gun. 4 rnd mag. Stick with AR, bolt or single shot. I have the 308, very nice. BO is fun too.
    9 replies | 177 view(s)
  • popper's Avatar
    Yesterday, 09:59 AM
    I think what you are doing is just cooking the water out. It sure does give a clean alloy. I cook for 1/2 hr min, stirring to get the Cu mixed in to all the alloy as it chemically combines - not just a mix. I don't see any problem with the way...
    7 replies | 401 view(s)
  • popper's Avatar
    Yesterday, 09:46 AM
    Choice of powder for that huge case might be a problem. Guess Unique, power pistol and maybe 2400? Look for plinker 06 loads.
    11 replies | 150 view(s)
  • popper's Avatar
    06-30-2022, 06:19 PM
    With either tin or zinc (cheaper) in the alloy, put copper sulfate on top, wait for it to turn white. Then mush carefully into the liquid till it stops bubbling. Stir it in and remove the 'dusty' junk on top. There is a sticky thread on it. Cu...
    35 replies | 937 view(s)
  • popper's Avatar
    06-29-2022, 02:53 PM
    Lino makes pretty bullets but 2% Sb works for all but HV rifle. Whole lot cheaper.
    19 replies | 566 view(s)
  • popper's Avatar
    06-27-2022, 02:17 PM
    All but 9mm will do fine with 1-2% Sb. 4% Sb for the rifles, heat treated. Adding Cu will help with the higher fps and fast twist. I've gotten alox to work OK up to 1800 (BLL), past that, little iify. PC works OK to 2700 in my 308. A quick tumble...
    35 replies | 937 view(s)
  • popper's Avatar
    06-24-2022, 02:16 PM
    You may need to get into PC coating. Most 30/30s need 310-311. My Marlin leaded with 310 store bought. Get a 311 Lee sizer. Al GCs are cheaper. Try without using 2400 or Unique for plinker rnds. Full length size for THAT gun. I've never trimmed...
    52 replies | 1429 view(s)
  • popper's Avatar
    06-24-2022, 01:52 PM
    popper replied to a thread Annealing question in Cast Boolits
    I don't induction anneal brass. That said, NO. Most 'hide' the neck from you so you can't tell. Anneal some at a specific time and test the anneal with needle nose pliers. Find the right time and set the machine.
    16 replies | 350 view(s)
  • popper's Avatar
    06-24-2022, 01:42 PM
    TV show of the football player and GF. He shot a 'goat' from 400 so yds, over a river. Had the knowhow - most don't. GF dropped the rifle and bumped the scope, missing most shots. Know your limits.
    100 replies | 2456 view(s)
  • popper's Avatar
    06-24-2022, 10:58 AM
    popper replied to a thread Cast AR-15 Upper build in Cast Boolits
    armor's kit why? All you need is an upper clamping block. Barrel nuts are flats for a wrench now. Many have tried the 223 cast, few have succeeded. Any 30 cal based on 223 case works fine and is much easier. My BO carbine gets 2" @ 100, 145gr PB,...
    21 replies | 599 view(s)
  • popper's Avatar
    06-23-2022, 03:16 PM
    you can't get subsonic in 30/30 with light bullets and rifle powder! Heavies and pistol powder. You can use 170gr PB and 2400 or unique to get 14-1700 fps to work. Above that GCs make it easier. Definitely you can get faster but not easily.
    52 replies | 1429 view(s)
  • popper's Avatar
    06-23-2022, 03:08 PM
    I use 'chaser' lower fps GC cast to clean rifle barrels of 'gunk'. Gunk may be slight leading, PC, powder residue, lube residue. Look at the target, almost always a dirty 'ring' around the hole from 'gunk' in the barrel. Any bullet will cleanout...
    12 replies | 1985 view(s)
  • popper's Avatar
    06-23-2022, 02:55 PM
    popper replied to a thread Ruminations in Cast Boolits
    OK, this doesn't happen, melting lead. However, cutting torch cuts by hot gas MASS and temp. Metal doesn't melt but only hot enough to reduce strength to the point of being blown away. Same with gas cutting of cast. High pressure and small exit...
    12 replies | 421 view(s)
  • popper's Avatar
    06-22-2022, 02:15 PM
    I thought about it about 5 yrs ago. They cast the receiver and then machine it - you could get a receiver only back then. Decided against it. Actually they were too busy making gattling guns then. Another guy in IIRC Nola builds a great one @ 5k$...
    15 replies | 628 view(s)
  • popper's Avatar
    06-22-2022, 02:10 PM
    popper replied to a thread Thoughts on Henry .308 in Leverguns
    Ar10 is probably 7.62x51, Henry is 308W - chambers are different. I just re-sized and trimmed a bunch of LC brass. Mine appears to have a SAMMI spec 308W chamber, it measures to spec! Henry did good. Going to load up some PCd 145gr GC for it too....
    9 replies | 725 view(s)
  • popper's Avatar
    06-22-2022, 02:01 PM
    Post #3 is the correct way. And remember to expand the neck for proper neck tension.
    29 replies | 629 view(s)
  • popper's Avatar
    06-22-2022, 01:59 PM
    Forget the GC for any pistol load. But fit and alloy come into play then. GC can cover up a lot of 'sins'.
    8 replies | 423 view(s)
  • popper's Avatar
    06-22-2022, 01:57 PM
    Guess I'm different. 4 GKs about 8 yrs old started with 12ga, 9mm, 40SW, 308MX. Single loaded until they get the 'excitement' out of their system.
    77 replies | 1257 view(s)
  • popper's Avatar
    06-22-2022, 01:49 PM
    Just make some Ben's Liquid Lube.
    15 replies | 421 view(s)
  • popper's Avatar
    06-22-2022, 01:47 PM
    For remote viewing/alarm, internet or cell phone service is needed and many of the cameras DON'T work with Windows. You could set up a local private wireless network but not what most manuf. want. Kinda like the ring camera, worthless without a...
    27 replies | 1004 view(s)
  • popper's Avatar
    06-22-2022, 01:38 PM
    Direct up load of video to tis site takes storage space that costs $. Hosting sites have a greater 'audience' therefore cost effect isn't so great. It's about $. I'll go through and delete some of my less 'important' posts to save space. Shooting...
    70 replies | 1923 view(s)
  • popper's Avatar
    06-20-2022, 11:15 AM
    170gr PB I use in BO AR pistol. Don't use it sub, about 1200 fps. Works fine and cycled OK. 31-168C. Use a 185gr version also but it's GCd, not needed for subs.
    4 replies | 163 view(s)
  • popper's Avatar
    06-18-2022, 12:58 PM
    popper replied to a thread D-Day in Our Town
    Not D-day but interesting. https://sensingonline.blogspot.com/2022/05/ Some religious context in it but good anyway.
    23 replies | 783 view(s)
  • popper's Avatar
    06-18-2022, 12:19 PM
    popper replied to a thread Investments in Our Town
    https://sensingonline.blogspot.com/2022/06/get-ready-for-catastrophic-def-shortage.html Very interesting, must read. Another funny one. https://sensingonline.blogspot.com/2022/03/biden-begs-texas-to-secede.html Read the bottom line!
    47 replies | 1584 view(s)
  • popper's Avatar
    06-17-2022, 12:56 PM
    popper replied to a thread Thoughts on Henry .308 in Leverguns
    Hammer extension grub screws didn't fit so CS sent me another. Great service.
    9 replies | 725 view(s)
  • popper's Avatar
    06-14-2022, 06:28 PM
    popper replied to a thread Places you have been in Our Town
    Spain, France, Italy, Greece, Mexico per Sam. Japan, Korea and Germany per work. Most of Canada east of Detroit. Can't think of a state other than Alaska & Hawaii I haven't at least driven through. Really don't care to go anywhere anymore. Well,...
    47 replies | 1512 view(s)
More Activity
About popper

Basic Information

Signature


Whatever!

Statistics


Total Posts
Total Posts
9,932
Posts Per Day
2.47
General Information
Join Date
06-28-2011
Referrals
0

2 Friends

  1. Blanco Blanco is offline

    Boolit Master

    Blanco
  2. Norcal707 Norcal707 is offline

    Boolit Man

    Norcal707
Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check