Inline FabricationRepackboxMidSouth Shooters SupplyWideners

Tab Content
  • fc60's Avatar
    01-20-2023, 09:11 PM
    Greetings, I recently melted down some MonoType letters into ingots. When melting, there will be a point where you get a "slushy/pasty" compound on the surface. This is the metal entering into the transformation from solid to liquid. Do...
    24 replies | 916 view(s)
  • fc60's Avatar
    01-19-2023, 12:51 PM
    Greetings, Phelps was located in Orange, New Jersey. They copied the Star and cut corners where possible to reduce costs. Not sure Star Greaser parts will fit a Phelps Greaser. Star reloader parts are not fully interchangeable with the...
    6 replies | 337 view(s)
  • fc60's Avatar
    01-18-2023, 03:10 PM
    Greetings, Go to the Magma Engineering website and download the Instruction manual for a Star Greaser. Operation is essentially the same. Cheers,
    6 replies | 337 view(s)
  • fc60's Avatar
    01-15-2023, 02:17 PM
    fc60 replied to a thread 0.392 Round Ball in Muzzleloading.
    Greetings, The only other clues I can offer are that it is a Hensley & Gibbs one-cavity mould. "392" stamped on the side of one block. A quick check with calipers suggest that it is 0.392". I will cast a few in the next week or so just to...
    7 replies | 341 view(s)
  • fc60's Avatar
    01-13-2023, 04:31 PM
    fc60 started a thread 0.392 Round Ball in Muzzleloading.
    Greetings, I have a 0.392" round ball mould. What rifle/pistol uses such a diameter? Cheers, Dave
    7 replies | 341 view(s)
  • fc60's Avatar
    01-07-2023, 08:52 PM
    Greetings, RCBS Pistol moulds are cut for 10:1 Lead:Tin alloy. Rifle moulds are cut for LinoType. Seems the harder the bullet the more springback from sizing. Dig out your Intrimik and measure the greaser dies. They are machined with...
    22 replies | 548 view(s)
  • fc60's Avatar
    01-06-2023, 01:26 PM
    Greetings, Just cast up some Lead hammers for my fellow casters. McMaster-Carr used to sell the mould and spare handles. No more. Apparently Lead is bad for you. Found the company that purchased the Cook Hammer tool. I was able to get two...
    24 replies | 1087 view(s)
  • fc60's Avatar
    01-05-2023, 08:14 PM
    Greetings, Did you use 99% Isopropyl Alcohol? The 70% and 91% contain oils. Cheers, Dave
    5 replies | 218 view(s)
No More Results
About fc60

Basic Information

About fc60
South Prairie, WA 98385


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 10:31 PM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check