MidSouth Shooters SupplyRotoMetals2Lee PrecisionInline Fabrication
Reloading UKTitan ReloadingRepackbox

Tab Content
  • fc60's Avatar
    09-14-2021, 12:28 PM
    Greetings, Thanks to happy7 for pointing out it is a split pin. I was under impression it was the sprue plate hinge screw. The pin can be removed; but, it is not an easy task. Cheers,
    6 replies | 164 view(s)
  • fc60's Avatar
    09-13-2021, 07:43 PM
    Greetings, Either Shilen, Krieger, or Douglas make a good rimfire barrel. All offer blanks that you turn down to finish diameter. Next decision is do I want CrMo or Stainless? Cheers, Dave
    7 replies | 305 view(s)
  • fc60's Avatar
    09-12-2021, 04:24 PM
    Greetings, There is enough material sticking out. You might try applying Kroil to the thread and let it soak for a day. Then, grip the screw with a small set of Vice Grips. Turn the screw back and forth gently while applying more Kroil.
    6 replies | 164 view(s)
  • fc60's Avatar
    09-06-2021, 07:27 PM
    Greetings, Search eBay for "Starrett 66". I got several hits and many are new in the box. The 0.0015" and 0.002" blades get damaged first on used sets. Look carefully and you should find a set for under $20.00.
    28 replies | 611 view(s)
  • fc60's Avatar
    08-26-2021, 07:51 PM
    Greetings, Ballisticast added "600" to all the H&G mould numbers. So, "616" - "600" = 116 The H&G #116 is an 8mm Nambu mould. From the H&G webpage...
    2 replies | 74 view(s)
  • fc60's Avatar
    08-25-2021, 03:32 PM
    Greetings, The last run of H&G moulds of 6, 8, and 10 cavity had a screw in the end of each handle. The metal handle was drilled and tapped. If the wood handle became loose, you merely tightened the screw slightly. Sourcing new handles...
    5 replies | 197 view(s)
  • fc60's Avatar
    08-25-2021, 03:19 PM
    Greetings, Watch eBay for a good used Star. Make sure it has all the bits and pieces. Many sellers have no clue as to what they are selling. Cheers, Dave
    45 replies | 1225 view(s)
  • fc60's Avatar
    08-24-2021, 01:52 PM
    Greetings, Try applying some Kroil to the screw and walk away for a while. Check with the dealer to ascertain if it is left or right hand thread. Cheers, Dave
    62 replies | 1537 view(s)
  • fc60's Avatar
    08-23-2021, 04:19 PM
    Greetings, Fill the pot, turn it on and let it stabilize. Loosen the set screw on the big dial and reset it to what your calibrated thermometer says. The joy of buying used equipment... Cheers,
    10 replies | 379 view(s)
  • fc60's Avatar
    08-21-2021, 12:29 PM
    fc60 replied to a thread Hg#38 ness safety bullet in Cast Boolits
    Greetings, I did find this in my archives... #38 - .30 Caliber. Ness Safety Bullet. Gas check base, two round grease grooves, no crimp groove, long straight parallel-full-length nose. Very large hollow point, which tapers to within .100" of...
    12 replies | 424 view(s)
  • fc60's Avatar
    08-20-2021, 04:31 PM
    fc60 replied to a thread I love quality tools! in Our Town
    Greetings, I, too, favor old tools. I set a search parameter within eBay so I get notifications of new listings of the tool I seek. I have been fortunate. Most sellers are clearing away an Estate and on occasion you get a like new tool with a...
    54 replies | 1730 view(s)
No More Results
About fc60

Basic Information

Statistics


Total Posts
Total Posts
105
Posts Per Day
0.03
General Information
Last Activity
Today 04:24 PM
Join Date
10-16-2010
Referrals
1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check